Subject: Turbocharger for the Renesis
From: paul lamar
Date: 11/19/2015, 5:39 AM
To: A10-Me-Earthlink


How do I get up to speed on selecting and connecting up a
turbocharger for my airplane?

Gary Schwarz

The bible on this subject is Turbochargers by Hugh MacInnes.

See the attached files. There are a couple of others that I listed
that are not bad.

By far the best web site.
https://turbobygarrett.com/turbobygarrett/turbo_tech_basic


The stock Mazda Turbo II manifold cracks. The second version is
better than the first and can be welded up and modified. radius all
sharp edges to at least 1/4 inch. Mazda failed to do that.

Top of the line is an Inconel manifold.

If not that make it out of .125 thick 321 SS tubing or plate.

Paul Lamar

Beautiful welding.

milo


A Maximite data acq system would be invaluable for a turbo
installation. The bottom line is how much boost do you get for x
amount of exhaust back pressure over a range of RPM's. That is
related to fuel burn. The Maximite will record at high speed up to
ten parameters.

One book I was disappointed in was Turbocharging Performance
Handbook by Jeff Hartman. Mostly just pretty pictures.


Paul Lamar

Gary:

I am working on a turbocharged RX-8 also--mostly due to the
complication of TIG welding up 6 x 20" intake tubes draped over the
top of the engine (bellmouthed into a plenum) for the naturally
aspirated intake-- and also the noise factor which would require at
least a 10 lb muffler.

It appears installing a turbo might be a wash in terms of labor to
weld intake and exhaust-and the overall weight (muffler possibly not
required for turbo version).

It appears an intercooler is a very good idea (if not required) as
the RX-8 has about a 10-1 compression ratio.

I am essentially looking to turbo normalize the RX-8 to get about
200-250 HP at any altitude < 18000' at 6000 rpm cruise and 7700 rpm
take-off (with Tracey's 2.85-1 reduction drive).

So far I have reduced the choices to:

T04E-50 trim, F1-62 turbine, A/R = 0.68 (possibly bigger). T4-4-bolt
flange, 3" dia. V-band outlet. 3" dia. compressor inlet & 2" dia.
outlet. External wastegate. See turbonetics catalog for details.

This is partly based on one flying in a Cozy IV with good results.

Let me know what you discover.

Regards,

Richard Craig

I don't recommend the six tubes over the top. It is much easier to
take the engine apart and p-port it. Just spend some time to make a
compartmented container to store all the seals so they go back in
exactly where they came out of.

The engine is a lot easier to take apart and put back together than
it looks. Don't be afraid of doing that. If you wish buy a old 12A or
13B and use it for practice. Download shop manuals from here.

http://foxed.ca/index.php?page=rx7manual

Plan B is wait awhile until we get a handle on the Helmholtz
resonator. If that works you can just cut off a stock RX8 intake
manifold and weld on a rectangular tube.


A turbo is a good idea as it gives a lot of power and 10,000 feet for
high speed cruise. It also replaces the muffler.

http://www.turblown.net/store/index.php?categoryID=22

Paul Lamar

I would recommend an A/R of closer to 1, maybe a bit higher. A low A/R is
useful to limit turbo lag in cars because it uses a smaller turbine wheel
and tighter case. This lets the turbine spin up fast and turn faster
resulting in less wait for the power surge. The first drawback for aircraft
use is that the smaller wheel gets a more concentrated heat load. Couple
that with its higher speed and you get premature failure. The second is
that since the turbine turns several times faster than the higher A/R
units, the shaft wear becomes an issue.
For mine, I have a T04 with an A/R of 1.06. It has a larger slower turning
turbine and a larger surface area for heat dissipation. I am also placing
it 18" downstream to allow the exhaust to cool before it reaches the
turbine. I work on aircraft, and my latest is a turbo Seneca II. Her turbos
are 1.06 A/R and have a TIT limit of 1500 degrees. My rotary exhaust comes
out single 2" tubes to a 2.5 then t a 3" before it enters the turbine. I
also have a cooling shroud similar to normal aircraft heater cuffs around
the exhaust to help cool the exhaust. This shroud coupled with the
expansion of the gasses should keep the TIT under control and keep my turbo
from failing.

So far the turbo failure mode for the rotary engines in aircraft has been
primarily due to heat. The stock turbo fails because the turbine gets hot
and centrifugal force stretches the metal to the point of contact with the
housing and failure. And, these turbos were meant for stoplight to
stoplight racing, not 8 hours of continuous use with 1800 degree exhaust.
My solution includes a turbine that will turn slower, dissipate more heat
and with the exhaust cooled should function well. It should be noted that
in every certified aircraft that I have worked on that has a turbo, they
are located way downstream of the exhaust ports in the engine. The Seneca
II (Connie 6 cyl IO 360) has all 6 cyls exhaust come into 1, it goes from
1.5 to 2" for about 6 inches, then into the turbine. My EGTs when leaned
run about 1350, my TIT runs closer to 1200. Cooler temps = happy engine.
Even the Cessna TTX which has 2 turbos, one on each side of an IO 550 has
the turbos located almost at the firewall as far from the exhaust ports as
they could get it.

As far as an intercooler, I would say definitely yes. Compressed air from a
turbo can reach 400 degrees plus. However, if you used a carb like the old
Chevys and some drag cars and place it upstream of the turbo the
evaporation of the fuel will cool it somewhat. The downside is that you
have a compressed fuel air mixture that in the event an intake hose comes
loose or leaks would become a very effective blow torch. Not recommended.

In Summary-

Larger preferably ball bearing turbo. Could also use a marine turbo, these
have water jackets for cooling and use the engine cooling water to keep the
turbo cool. You would need a bigger radiator.

A/R of 1 or better, particularly on the turbine side. Mine has a .96 on the
compressor side.

Mount the turbo behind the engine, put as much room for cooling between the
engine and the turbo as you can.

Enlarge the exhaust to encourage expansion as this will cool the exhaust.

Shroud the exhaust and feed it with SCAT tubing forced air that dumps
overboard.

Oil- the aircraft turbos feed oil from the BOTTOM and it is returned to the
TOP of the engine in the accessory case so that at no time can the turbo
not be FULL of oil. No gravity return and drip like cars do. Comes in at
3/16 leaves in 1/4. This arrangement also lends itself to the installation
of a small oil cooler to cool the oil before it dumps back into the sump.

Kevin Alderman
A&P, GROL, CFI (the last ones are new letters ☺ )


Well put. You amaze me Kevin :)

Paul Lamar


The Rotary Engine News Letter. Powered by Linux. If you want off the
list PLEASE let me know and I will remove  you.  ACRE NL web site.
http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
Copyright 1998-2015 All world wide rights reserved.