Subject: Fwd: Re: SPAM --rotor and housing material questions........
From: paul lamar
Date: 1/16/2016, 7:01 PM
To: A10-Me-Earthlink




 So, rotors are usually for the RX-7 are cast iron? The housings are
 aluminium with a thin layer of nickel for the wear surface?

 Does anyone know what the Johnson or Sachs small snowmobile engines
 used for their rotors and housing? I have been told by one person
 that the rotors are cast iron too but the housings are just
 aluminium.

 Does anyone know if just plain aluminium housing are used? Any other
 material used for rotors besides cast iron that works?


 David Jr.

 Yes the rotors are cast iron. Very tough and robust. The housing are
 lined with hardened steel and then chrome plated.

 There have been many different coatings applied to the aluminium with
 out as much success as the Mazda housings. 2.5 million engines have
 been sold.

 Paul Lamar

 Great pictures, thanks Paul. I would take as many of those production
 pictures and such that you would like do send.

 David Jr.

 Here are a bunch more. We were the first round eyes to get a tour
 through the factory :-) Took 18 months of cajoling.

 Paul Lamar



Great pictures!  I've been working on some investment casting (steel and
aluminum) using sterolithography to generate the wax molds.  It appears
that the rotor would be an ideal part to make using that process. For
ones or twos, it is much cheaper than having to make a mold.  If larger
quantities are needed, then they make a wax mold from the stereo model.
This method sure beats the old way of making patterns.

Gary Knutson

I made some intake patterns on the local college stero lith machine back
in 2003. In those days the stero lith machine cost $30,000.


Paul Lamar

Could the rotors be 3D printed from say Titanium or other materials at a
realistic cost? The weight of the rotor would be so reduced that RPM
could be increased. The printing would allow a design that would not be
practical or even possible with conventional machining or casting.
I think that NASA is able to print in different metals without the
conventional welding process.

Andrew Campbell.


As long as it can hold the tolerances to + or - .001 inch.

Paul Lamar


Andrew, Paul,

3D metal printers are unable to maintain 0.001" tolerance The challenge is pretty complex. For one thing the typical fine granularity metal powder is roughly 45 microns or nearly 0.002" so even this fine powder appears like big boulders at that level. Second, the powder is held in place with the adjacent powder while laser "melts" small particles and bonds them to the layer below and adjacent powder. the powder shrinks as it's melted when the gas is released from the crevices between the particles. Lastly, the laser spot size is really difficult to control at all times because the depth of focus varies as the beam moves. Most printers are employing correcting lenses but they are not perfect. the effects of the above are compounded hence the it will be many years possibly decades before we get to that kind of tolerance from metal 3D printers

Last but not least, the cost. You might as well turn over the deed to your house. Last figure I had, was that 3D Aluminum powder was $114 per pound, so you can imagine that Ti would be significantly higher. My gut feel is that by the time all is said and done, the cost will be prohibitive. The 3D metal printers start at around $500K and go up to $2 million and even a 2" wide rotor will require ~1,000 minutes and closer to 1500 minutes for a standard 8 cm rotor. Essentially you tie up an expensive tool for 2 days (one shift) and someone has to pay for it. btw, I am working on a patent to overcome these limitations but had to set it aside due to other priorities

Assuming you are willing to pay a premium, there is a possible way around the 3D tolerance limitation. You print the shape on the low side on all dimensions ie 2 to 3 thou short. Then apply a Nickel plating or appropriate metal coating in the 4 to 6 thou thickness range (may need to go thicker), and then machine down the surface to the original dimensions. Depending on the roughness of the 3D printed part, you may be able to fill in the crevices sufficiently to end up with sufficient acceptable surface quality
Regards,
Simon Saba

Where 3D printing my pay off big time is in the core boxes.
It did for me. A pattern maker wanted to charge me $5000 dollars for an intake
manifold pattern.

Paul Lamar


 The Rotary Engine News Letter. Powered by Linux. If you want off the
 list PLEASE let me know and I will remove  you.  ACRE NL web site.
 http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
 Copyright 1998-2016 All world wide rights reserved.