Subject: Welding the cross counter flow rads.
From: "rotaryeng@earthlink.net" <rotaryeng@earthlink.net>
Date: 1/18/2016, 11:44 AM
To: A10-me-earthlink




The dodge 1500 truck rad core is 31 5/8" x 19 3/16" x 1", wouldn't that give around 600 cubic inches? Or will that be doubled by having 2 of them in the cross counterflow? The newsletter reply below is showing 465 cubic inches for that rad,did I pick the correct rad measurements? Trying to size a rad to fit the cowl of p-port rx8. Laying down vs upright on the cool side of cowl.
https://www.radiatorexpress.com/product.asp?part=2001+DODGE+RAM+1500+PICKUP++-+5%2E9+liter+V8+RADIATOR+STOCK+REPLACEMENT%2C+31+X+19+CORE&part_id=218342&aaia_id=1366590



The oil cooler we have is CXRacing with core of 13" x 9" x 2" which is only 198 cubicinch. I read an old reply from Neil Unger that around 300 cubic inch for 250hp is good for oil cooling?
http://www.cxracing.com/mm5/merchant.mvc?Screen=PROD&Store_Code=CXR&Product_Code=OC-248-30-AN10&Category_Code=OILC

-Matt Boiteau

- Matt

On Sat, Jul 18, 2015 at 4:05 PM, paul lamar <rotaryeng@earthlink.net <mailto:rotaryeng@earthlink.net>> wrote:



    Cross counter flow is a more effective heat exchanger.

    Here is the sequence for welding the rads to make a cross counter
    flow heat exchangers.

    Butt tig weld the in and out tanks first by cutting off all tabs on
    the rads.

    Don't weld the in and out tubes on yet.

    They will be marked for position on the tanks while on the aircraft.

    Then the large holes for the tubes will be cut and then the tubes
    will be welded over the holes. The tank design will vary depending on
    cool side mounting or bottom mounting. The TTC is a bottom mount.
    Most other aircraft use a cool side mount. The 3 rotor allows longer
    rads to be used. Put the diffuser between the rads and the engine.
    See my book How to Cool your Wankel for more info.

    After the tanks are done (with out the holes and tubes) bolt the
    rads together with the wood strips leaving 1/2 to 3/8 of an inch
    between in and out tanks.

    The idea here they must not touch each other. The wood strips are
    heat insulators between the two rads.

    Then weld an aluminium strip 1/2" to 3/8" wide at the other end.
    Finish by boxing in the other end (the front end).

    Weld on them some and let the rads cool some what. They are brazed
    together at only 1100 F so it is important to not get them too hot.
    Wet rags around the ends of the fins and tubes might help.

    Here are a bunch of pictures attached. The JPGs were Dodge Neon rads
    and not the truck rads. The TTC rads will be welded soon.

    Apparently when Mercedes owned Chrysler they implemented some up to
    date heat exchanger technology. IMHO Chrysler rads are now the best
    from an efficiency point of view I have found so far. Honda also uses
    up to date tech but they are more expensive.


    Paul Lamar



    What about a dual pass rad already done?
    http://www.jegs.com/i/Allstar-Performance/049/ALL30048/10002/-1

    -Matt Boiteau


    It will probably work but you will be paying a weight and drag penalty.
    I don't know how much on the drag penalty. We don't have any comparison data
    on the drag yet. The weight of the core with water will be at least
    150% of the cross counter flow Dodge truck rads.

    Paul Lamar

    For maximum efficiency, you don't want to use the flow pattern described in
     their (Allstar's) text, use the pattern from Paul's book. The top core (or first core
    exposed to cooling air) is the second core the coolant flows through.

    This better utilizes the Delta/T thermal transfer to the cooling air flow. Read Paul's
    book for counter cross flow cooling theory.

    C. Smith

    Craig, can you send me that Allstar text. I found their web site but I can't find anything
    about that. Apparently they use two rows of one inch tubes . The Dodge truck rad is one
    row of .7 inch tubes.

    http://www.allstarperformance.com/instructions.htm

    In theory one could cut the All Star rad apart into a top and bottom for a cross counter flow
    reconfiguration. That would give more core volume if two Dodge truck cores were
    not enough core volume . Slightly less efficient however.


    The basic idea is you want as large a frontal area you can fit in the cowling with core
    volume of about 500  inches. The Dodge truck core are about  465 cubic
    inches and will probably work with 250 HP. We now have about 930 cubic inches
    in the time to climb rad which I am guessing will be good for about 500 HP.

    I suspect the time to climb cross counter flow rad is not enough core volume for 650 HP and
    we will have to spray cold water on the assembly.

    We used to think we needed 650 cubic inches for 250 HP and that was before we discovered
    the the much improved Kays & London wedge diffuser.

    Ian in Perth Oz did some experimenting  with a Kays & London  S shape diffuser lying
    on it side and was able to reduce the size of the air intake to 10 to 15%
    of the core frontal area. That, in theory, reduces the cooling drag. Ian  routinely flies
    around the outback.

    Ian has  built two RV6's powered by rotaries. The first one crashed when a hose
    blew off a rad with out a bead on one of the tubing ports.

    Paul Lamar

Do we have any more pictures of Ian in Perth Oz, S shape diffuser lying on it side ?

  -Matt Boiteau

None with the cowl off.

Paul Lamar


The Rotary Engine News Letter. Powered by Linux.
If you want off the list PLEASE let me know and I will
remove  you.  ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2016 All world wide rights reserved.