Subject: New alloy to put turbo compound rotaries on the map
From: "rotaryeng@earthlink.net" <rotaryeng@earthlink.net>
Date: 2/6/2016, 7:58 PM
To: A10-me-earthlink



     It is called MA 956.
                 Since the rotary exhaust temperatures are up around
                 1800 F it will be needed. One can always cool the exhaust
                 before it goes to the turbine but that implies a loss
                 of recovered energy.


                 Paul Lamar

             Hi Paul & Steve
             Looks like engine rotors from this alloy would have to be CNC
   machined from solid billet or forgings.
             It is NOT a castable material (unless you are willing to lose
   the special high-temp qualities) :

             >From Special Metals - "INCOLOY® alloy MA956 (UNS S67956),
   first developed as an aerospace superalloy and now used in a range of
   industrial applications, combines excellent strength and fabricability
   with outstanding resistance to prolonged exposure up to 1300°C (2400°F).
   Its exceptional properties result from the mechanical alloying process
   by which it is made; a process which allows a fine distribution of
   yttrium oxide particles to be incorporated into a highly
   corrosion-resistant Fe-Cr-Al alloy"

             >From Matweb - "An iron-chromium-aluminum alloy that is oxide
   dispersion strengthened and produced by mechanical alloying"

             >From wiki - "Incoloy MA956 is made by a mechanical alloying
   <https://en.wikipedia.org/wiki/Mechanical_alloying> rather than a
   bulk-melting process"

             Cheers
             Paul Randal


         How big of a billet would be needed to make some 12a sized rotors
   out of this material? I know it's overkill but I am curious.

         Steve Ross

         My guess is 12 inches in diameter.

         Paul Lamar


   Weight or density is the problem. There is no advantage over the stock
   rotors.
   Titanium or titanium aluminide rotors would cut the rotor weight in
   almost 1/2.
   If you build a larger rotary engine such as the R130 or the new 16X the
   rotor weight is even more. Manufacturing the rotors from TiAl would have
   a pronounced effect on the weight. I am not certain about the heat
   transfer of TiAl but being 50% aluminum it should be similar or higher
   than the cast iron rotors. A titanium rotor would save weight and have
   low heat transfer similar to SS which could provide an ideal rotor
   material other than cost.
   That should start coming down as it is used more in aerospace and racing.

   Dale Davies


   See attached data sheet for available sizes. May not be available in
   sizes large enough to make rotors.
   Larry Childs

   There is little advantage in building lighter or stronger rotors over the stock units. The mass of the stock rotor is part of the flywheel effect needed by the rotary to smooth out the power pulses.

When the car accelerates, or the aircraft climbs, the rear rotor collects more hot oil than does the front rotor. The weight of that extra oil produces an obvious imbalance between the two rotors. However the nearly 10 pounds of the rotor is little modified by the extra oil, and the imbalance is not noticeable. Not the case with a very light rotor. The oil becomes a higher percentage of the total rotor weight. That mass also protects the bearings against detonation shock loads and against misfires. The stock rotors are little affected by heat, are repairable by welding and brazing and are relatively inexpensive. If Mazda did sell aluminum racing rotors you wouldn't want them in an airplane. You would have to add large amounts of flywheel to keep from shaking the gearbox and prop hub to pieces. We have been turning stock 12A rotors over 9,000 RPM since the 70s with just a flex plate for a flywheel. The stock rotors are much more than adequate for aircraft use.

Lynn E. Hanover


   The Rotary Engine News Letter. Powered by Linux.
If you want off the list PLEASE let me know and I will
remove  you.  ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2016 All world wide rights reserved.