Subject: Turbo-side-Time to Climb 650 HP
From: "rotaryeng@earthlink.net" <rotaryeng@earthlink.net>
Date: 2/14/2016, 3:12 AM
To: A10-me-earthlink



    I forgot to mention the Bell is 3:1.

    The Allison version will be in the same ball park.

    BTW rumour has it the new RXx will be 3.2 litres equivalent so at the
    same level of tune as the current 13B  TTC engine we are looking at
    800 HP for a two rotor. It is all aluminium stock as well.


    Paul Lamar


    Paul, you might look at the gear set from a NP241 transfer case, it's
    very beefy and it doesn't have a lot of crap attached to it. Ratio is
    2.72:1.

    Everett Rankin

    How much torque is it good for?

    Paul Lamar


    Supposedly 5500 lb-ft, like I said, it's beefy;)



http://www.genuinegmparts.com/pdf/powertrain/GM%20Parts%20Remanufactured%20Transfer%20Case%20Specification%20Chart.pdf



    Everett Rankin


    I doubt that. I think you mean 550 ft pounds. The ratio is too low
    for rotary use. We need 3;1 minimum.

    The Ford is good for 650 ft pounds and is used in the power stroke
    diesel. It is also 3.12 to one.


    Paul Lamar

    The chart reads 5000 lb ft. The input to the transfer case is the
    engine torque x torque converter x first gear ratio. The other
    thought with regard to this is the fact that low range used in a
    transfer case is designed only for short term intermittent use. When
    you go to the Allison MD 3060 transmission, the first gear is
    designed for 900 lb ft input torque and use in cement mixers etc.
    for use around town. Heavy loads and lots of red lights. In the
    specifications there is a maximum RPM input listed. That more
    pertains to the torque converter than to any other component. An
    advantage to the Allisons is that many of the planet carriers are
    rebuildable with planet gear kits. If they survive construction sites
    in trucks and other equipment in mud and God only knows what else,
    they will work real well as an aircraft PSRU.

    Dale Davies

    Must be for some sort of truck. The weight is 75 to 100 pounds.
    Totally out of the ball park for our applications. The Ford planet
    set weighs 8 pounds.

    The complete Bell 47 Gear box is only about 45 pounds. About the same
     as a Tracy. And that is a monster planetary.

    Paul Lamar

    It came in lots of 90's pickup trucks, not necessarily heavy duty
    ones.  That weight is for the whole transfer case, I don't know the
    weight of the gears but it'd have to be less than the Bell47. I
    thought about input RPM issue but the big diesels usually connected
    to the Allisons redline at around 3000RPM which is the maximum RPM
    the planetary input would ever see.  A pickup truck with a gas V8 on
    the other hand could see transfer case inputs of 5000RPM+ if it was
    used hard (transmission in top gear, 1:1).  It might actually be
    better. I'm not trying to rubbish your plans Paul, I'm just sayng
    that there are lot of interesting planetaries in transfer cases.

    Everett Rankin

    Let me know if you find any that are over 3:1. Also the Ford set are
    less than $200.

    Paul Lamar


   4:1 https://teraflex.com/shop_items/528ffa7fead962f416e72e96 35# with
   housing

   David Josephson

   I think the chain enters into the reduction. If the chain is 2:1 the planetary
   is 2:1 as well.


   Paul Lamar

The Allison input max RPM is not limited by the planetary gear set
but the torque converter.
As to the transfer case reduction. The chains are 1:1 as the front and
rear have to be the same.

Dale Davies


   The Rotary Engine News Letter. Powered by Linux.
   If you want off the list PLEASE let me know and I will
   remove  you.  ACRE NL web site. http://www.rotaryeng.net
   You Tube http://tinyurl.com/beqqxas
   Copyright 1998-2016 All world wide rights reserved.