Subject: 3 rotor turbo Reno Racer.
From: "rotaryeng@earthlink.net" <rotaryeng@earthlink.net>
Date: 3/4/2016, 10:49 AM
To: A10-me-earthlink



I am thinking about building a Reno Racer.
We need about 800 to 1000 HP to blow the rest of those guys into the weeds :-)

First hurdle is coming up with a gear box.
I can't afford $35.000 for a bell final drive so I investigated the Allison 1000 truck transmission.

Rumour had it it was 4:1 but that is not the case for a single planetary set. P3 on the Allison is 3:1 when you hold the ring gear fixed, take power out of the planet carrier and put power into the sun gear.
The output will rotate in the same direction as the engine.

You get the ratio by dividing the ring gear diameter by the sun gear diameter and adding one.

Here is a picture compared to the Ford unit most people are using now for most rotary powered air planes.

Looks good for a 1000 HP 3 rotor engine.

A lot of the stuff attached to the ring gear will be machined away.

Paul Lamar

I have decided to build our own planet carrier out of 7075T6 and add two pinions. Six total up from four. 50% more torque capabilities.

The Allison planet carrier is too hard to machine.

The planet parts are low cost. There are a million Allison 1000 out there.

Here is what it will look. We will keep the .75 dia. planet shafts and EDM a 1/2 inch hole in them for the prop shaft flange. Hardness and smoothness are retained. Lower cost than making new shafts.
The back of the planet carrier is smooth for a pusher thrust bearing.

The Allison has a much better input shaft and the required splines to the sun gear for our purposes than the Ford.

I talked to Kyle Mohan yesterday about his 3 rotor Drift engine making
800 to 950 HP
with side ports no less. It is running on gasoline. The turbo charger is smaller than the time to climb turbo. A Turbonetics GTX 750.
He has 20 races around the world on the engine so far with out rebuilding it.

Much thanks to my auto transmission expert Donny Caccamise that has helped us over the years.

Paul Lamar

The prop situation is not as bad as I thought.
Here are some charts generated by a BASIC program of tip speed verses RPM. We will see what RPM the time to climb engine achieves to see how well the Catto 84 inch  prop deals with tip speed. This also helps the gear box as the shaft stress is reduced with a constant 1000 HP at a higher shaft  RPM than 2000. The shaft diameter is between 50 mm and 60 mm depending on what needle bearing I can buy.

I have yet to calculate the tip speed at 400 MPH AC speed.
That can be done with a modification of the BASIC program.
It will be a max of 1.3 times the radial tip speed.

If we are lucky the TTC engine will achieve 7500 RPM with the
3:1 gear box.   I can hardly wait :-)

More on this soon.

Paul Lamar


Paul,
We changed the nose case on Steadfast to speed up the prop from .7 to .9 mach at the tip at race speed. It didn't add any speed! It made the plane smoother as we were able to run a better prop combination, but as it came out, that same prop on the slow nose case gave us the same speed.
If you want to go really fast at Reno, think three things....... aerodynamics, aerodynamics and aerodynamics. Drag reduction is the easiest way to go faster! The brute hp method works, but at a price, and drag reduction has far better yields. A very low drag airframe will beat them at much lower hp numbers. Not that I don't like HP, but I can tell you for a fact where we found the speed in Steadfast.
Larry Child


Well that is fine but I don't have the money or time to design a new Sport Class racer.
As I understand the Sport Class rules you need to sell x number of kits to qualify.

I know top speed is the cube root of HP.

I was planning on buying a flying Glasair and using that. I think a GlasAir is now going over 400 MPH.
A few aerodynamic tweaks may be possible.

I will be happy if we can just stay with them :-)

Weight is also a big factor as when you are pulling a steady 3 or 4G's

Paul Lamar

The Rotary Engine free News Letter. Powered by Linux.
If you want off the list PLEASE let me know and I will
remove  you.  ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2016 All world wide rights reserved.