Subject: 3 rotor turbo Reno Racer.
From: "rotaryeng@earthlink.net" <rotaryeng@earthlink.net>
Date: 3/7/2016, 3:35 PM
To: A10-me-earthlink


I am thinking about building a Reno Racer. We need about 800 to
1000 HP to blow the rest of those guys into the weeds :-)

First hurdle is coming up with a gear box. I can't afford $35.000
for a bell final drive so I investigated the Allison 1000 truck
transmission.

Rumour had it it was 4:1 but that is not the case for a single
planetary set. P3 on the Allison is 3:1 when you hold the ring
gear fixed, take power out of the planet carrier and put power
into the sun gear. The output will rotate in the same direction
as the engine.

You get the ratio by dividing the ring gear diameter by the sun
gear diameter and adding one.

Here is a picture compared to the Ford unit most people are
using now for most rotary powered air planes.

Looks good for a 1000 HP 3 rotor engine.

A lot of the stuff attached to the ring gear will be machined
away.

Paul Lamar

I have decided to build our own planet carrier out of 7075T6 and
add two pinions. Six total up from four. 50% more torque
capabilities.

The Allison planet carrier is too hard to machine.

The planet parts are low cost. There are a million Allison 1000
out there.

Here is what it will look. We will keep the .75 dia. planet
shafts and EDM a 1/2 inch hole in them for the prop shaft
flange. Hardness and smoothness are retained. Lower cost than
making new shafts. The back of the planet carrier is smooth for a
pusher thrust bearing.

The Allison has a much better input shaft and the required
splines to the sun gear for our purposes than the Ford.

I talked to Kyle Mohan yesterday about his 3 rotor Drift engine
making 800 to 950 HP with side ports no less. It is running on
gasoline. The turbo charger is smaller than the time to climb
turbo. A Turbonetics GTX 750. He has 20 races around the world
on the engine so far with out rebuilding it.

Much thanks to my auto transmission expert Donny Caccamise that
has helped us over the years.

Paul Lamar

The prop situation is not as bad as I thought. Here are some
charts generated by a BASIC program of tip speed verses RPM. We
will see what RPM the time to climb engine achieves to see how
well the Catto 84 inch  prop deals with tip speed. This also
helps the gear box as the shaft stress is reduced with a
constant 1000 HP at a higher shaft RPM than 2000. The shaft
diameter is between 50 mm and 60 mm depending on what needle
bearing I can buy.

I have yet to calculate the tip speed at 400 MPH AC speed. That
can be done with a modification of the BASIC program. It will be
a max of 1.3 times the radial tip speed.

If we are lucky the TTC engine will achieve 7500 RPM with the 3:1
gear box.  I can hardly wait :-)

More on this soon.

Paul Lamar


Paul, We changed the nose case on Steadfast to speed up the prop
 from .7 to .9 mach at the tip at race speed. It didn't add any
speed! It made the plane smoother as we were able to run a
better prop combination, but as it came out, that same prop on
the slow nose case gave us the same speed. If you want to go
really fast at Reno, think three things....... aerodynamics,
aerodynamics and aerodynamics. Drag reduction is the easiest way
to go faster! The brute hp method works, but at a price, and drag
reduction has far better yields. A very low drag airframe will
beat them at much lower hp numbers. Not that I don't like HP, but
I can tell you for a fact where we found the speed in Steadfast.
Larry Child


Well that is fine but I don't have the money or time to design a
new Sport Class racer. As I understand the Sport Class rules you
need to sell x number of kits to qualify.

I know top speed is the cube root of HP.

I was planning on buying a flying Glasair and using that. I
think a GlasAir is now going over 400 MPH. A few aerodynamic
tweaks may be possible.

I will be happy if we can just stay with them :-)

Weight is also a big factor as when you are pulling a steady 3 or
4G's

Paul Lamar

Larry, do you have my book How to Cool Your Wankel ?

If you apply the Kucheman & Webber curve on page 29 to the
inside of your cowl you can cut down on some of the opening area
and in theory reduced the cooling drag. This was done on late
radial engines like the Super Connie.

Paul Lamar


Paul, Don't think I have it. I have many of the old docs from
NACA on cooling the radial (and water cooled) engines. There was
great research done late in that engine era that never went into
 production as the jet age took over. We used the data to redo
the engine cooling on Steadfast and gained lots of speed. The
other area we gained lots of speed was getting the airframe
straight so the plane flew with no trim at speed. On sport class
airplanes there are many areas to reduce drag and I will go over
them when you are here. I have a friend who does drag reduction
design work that is very interesting and has been used on
several very fast sport planes as well as the jet class. Larry
Child.

OK Larry Thanks.

Paul Lamar

Here is the effect of 400 mph aircraft forward speed  on the
prop tip vector speed at various RPM's and diameters. It is the
square root of the sum of the forward speed squared and the
square of the tip tangential speed.

QuickBASIC is invaluable for these kinds of calculations. I have
an old windows computer that still runs QB in a command window.

Looks like we will need  5 wide blades at 2000 RPM and 68 inches
in diameter to absorb 1000 HP. Perhaps we can get a surplus
C130J prop :-) I keep saying the Mazda Wankel is as good as a
turbo prop.

We also need a 4:1 gear box but we can get along with 3:1 if we
up the boost. This will be a severe test of the Mazda Wankel
structural strength.

My guess on why that GlasAir is going so fast in the Sport Class
is he has geared his engine about 2 to 1 and he is running it at
4000 RPM or above.

Paul Lamar

FYI, that transfer case I was talking about comes in a 4:1
version.

Everett Rankin

"The NP241 was manufactured with drop output on both drive and
passenger side and has a low gear ratio of 2.72 to 1. This unit
has combination of 2WD, 4W high and 4W low. The units are
provided with various front inputs, output splines and utilizes
a both fixed and rear slip yokes. "

The information I have is 2.71, You can tell by looking at the
picture of the planet carrier. Divide the OD by the ID and add 1.
High is just one to one.

Paul Lamar



The version in newer Jeeps is 4:1.
http://www.advanceadapters.com/tech-vault/5-new-venture-241or-roctrac/





Everett Rankin


http://www.4wheelparts.com/hardparts/HP_PartList.aspx?hpDID=346

"The NV241OR (Rock Trac) transfer case came out in 2003 with its
 all-new 4:1 low-range ratio from the factory. It is used in the
2003 to 2016 Wrangler Rubicon’s only. To identify if it’s a
NV241OR (Rock Trac) the round ID tag on the back half of the
case will have an OR (off road) after the NV241 number. If no tag
is present look at the input side of the housing it will have
additional overlap around the input assembly. This was required
to house the larger planetary gears, and the rear case half has
generous ribs to handle the increased torque afforded by the
lower gearing."

This is a picture and it is not 4:1. If the ring gear and OD of
the planet carrier is 6 inchs the ID MUST BE TWO INCHES!!!!!
This is not TWO INCHES!!!

The picture they are showing on the web site is NOT a 4:1 planet
 carrier!

Get a picture of the planet carrier and send it to me.

Paul Lamar


Yeah, that's probably the wrong pic.  I seriously doubt Jeep has
been lying about the ratio and nobody's noticed in 10+ years and
millions of units.

Everett Rankin

That outfit is in LA. I will call them tomorrow and go down
there and take a look. If it looks good it is a break trough.
That means we can run the engine at 8000 instead of 6000 with a
lot less boost.

Paul Lamar


Paul I am sure that with your collaboration with Mederer that
getting the horsepower you need for a successful Reno Racer is
not the paramount issue. However, it seems that the sustained
performance may be an issue. Have you thought about running
three turbochargers? I would think that three smaller
turbochargers (T3?), one per rotor would be able to take the
sustained abuse better than a single or sequential setup. A three
turbo setup would obviate an expensive inconel manifold and would
absorb the heat better, Just a thought.....

Alan MullenColorado

Your right. Good idea. Three exhaust pipes and intake ducts.
Easy to fit them in here.

I have also decided to do an engine oil pressure fed gear box
using Chevy 2.45" diameter V8 main bearing shells. That way we
can run the free constant speed Hartzel Reno racing props just
like everybody else. The prop gov can be cog belt driven off the
 back of the 3 rotor.

Paul Lamar


Another bearing choice could be the Ford 351W mains with a 3 inch
journal diameter. Depends on what the engineering numbers for
strength and availability dictate. If you need journal style thrust
bearings, the Detroit Diesel L53 and V92 series thrusts could be
paired with oil pressure feed between.

Dale Davies On Mar 7, 2016 11:29 AM, "Dale Davies"
<dale.davies.40.ford@gmail.com wrote:
Another bearing choice could be the Ford 351W mains with a 3 inch
journal diameter. Depends on what the engineering numbers for
strength and availability dictate. If you need journal style thrust
bearings, the Detroit Diesel L53 and V92 series thrusts could be
paired with oil pressure feed between.

Dale Davies


Two inch is plenty strong enough. 2.5" gives better support to the
planet carrier and prop flange.

Paul Lamar

The Rotary Engine free News Letter. Powered by Linux. If you want
off the list PLEASE let me know and I will remove  you. ACRE NL
web site. http://www.rotaryeng.net You Tube
http://tinyurl.com/beqqxas Copyright 1998-2016 All world wide
rights reserved.