Subject: More power for the road racers.
From: "rotaryeng@earthlink.net" <rotaryeng@earthlink.net>
Date: 4/25/2016, 6:22 PM
To: A10-me-earthlink



 The current intake manifold the road racers is not tuned. The rotary
  demands a tuned manifold.

 That is why Mazda spent so much time and money designing a very
 complicated tuned  manifold for the RX8. They succeeded wonderfully
 with almost a flat torque curve from 3000 RPM to 9000 RPM. This is
 also extremely important for low BSFC throughout that RPM range.

 Keep it in sixth gear around town and you will get over 20 MPG. 25
 MPG on the highway.

 The SCCA road racers on the other hand just need a lot of HP in the
 8000 to 11,000 RPM range.

 Peak HP at 8000 RPM requires a tuned length of 10 inches. The
 manifold most use now is not tuned. Here is a picture of that
 manifold.

 Side ports are required in most of the SCCA classes. P-ports are not


 The current intake manifold the road racers is not tuned. The rotary
 demands a tuned manifold. That is why Mazda spent so much time and
 money designing a very complicated tuned  manifold for the RX8. They
 succeeded wonderfully with almost a flat torque curve from 3000 RPM
 to 9000 RPM. This is also extremely important for low BSFC
 throughout that RPM range. Keep it in sixth gear around town and you
 will get over 20 MPG. 25 MPG on the highway. The SCCA road racers on
 the other hand just need a lot of HP in the 8000 to 11,000 RPM range.
 Peak HP at 8000 RPM requires a tuned length of 10 inches. The
 manifold most use now is not tuned. Here is a picture of that
 manifold. Side ports are required in most of the SCCA classes.
 P-ports are not allowed. P-ports and reasonable car weight with out
 ballast would put any rotary powered car at the top of all the
 classes in terms of  low lap times. It would then be pointless to
 race most of the other old piston powered cars most people race. The
 RX8 with 200 pounds of ballast dominates stock classes on the west
 cost. So one will need 4 side port runners 10 inches long. The way to
 do that is use two 40 MM weber copy carbs. Each carb has two throats.
 Mazdatrix sells them. Total length from port to the top of the bell
 mouth. For best results keep the bell mouth as short as possible. You
 will also need a cold air box on top of both carb as there is a lot
 of fuel mist that hovers above the tuned intake carbs. You can see
 that in this you tube video.

https://www.youtube.com/watch?v=NKJ00JsnS8AThis has been done on high
 power VW's and Porsches for years. Here are some 3D's and photo's on
 the subject.


 Paul Lamar



 Hello PaulI'd appreciate your thoughts on using Mikuni motorcycle
 carbs as  Tracy Crook did originally before developing his EFI.

Dave R

They worked sort of but not as well as a weber or weber copy.
Is this a car or airplane? There is no room in an airplane for
the weber if the engine is run upright.

If it is an airplane the exhaust down rotation works well with
a weber. It is not necessary to use an aluminium center housing
if the stock cast iron center housing is modified for rotor cooling
oil drain back.

A 500 CFM Holly 2 barrel would work even
better as a leaning kit can be bought for them.

Here are some pictures and 3D's.

Paul Lamar


The Rotary Engine free News Letter. Powered by Linux.
If you want off the list PLEASE let me know and I will
remove  you.  ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2016 All world wide rights reserved.