Subject: double the RPM double the HP.
From: "rotaryeng@earthlink.net" <rotaryeng@earthlink.net>
Date: 4/29/2016, 7:28 PM
To: A10-me-earthlink

I found this excerpt in a book I had called
V10 Formula One Technology by Ian Bamsey.

If we made rotors out of Beryllium Aluminium alloy
it would reduce the rotor weight to 2.1 pounds
from 9 pounds currently roughly. That would double the RPM
as the limit is controlled by the rotor bearing load.

Beryllium Aluminium is they only light material that
will withstand the heat of a rotor.

Quote:.

And this coming season the peak power speed will be over 18,000?

"We are always trying to increase it but for 2001 we have got a regulation change - the new materials limitation."

When we spoke in 1997 you were still using pistons made from the traditional RR58 aluminium alloy. At the time, nobody seemed to have a better alternative. Using RR58, piston cooling was an issue so you had an oil spray to the underside of the crown. Was cooling still an issue with the lightweight, relatively high heat rejection, aluminium-beryllium pistons you have used over the last couple of years?
"Yes - they still contain aluminium and the issue is still there!"

How significant was the introduction of the aluminium-beryllium piston?
"The properties of the material had certain benefits, no question. But it also posed problems, including machining problems. It was a step.
With the change in regulations which outlaws this material for 2001 we have had to do quite a lot of work in developing an alternative." Is your alternative an MMC material?
"No, it is an aluminium alloy. With the regulations as they are now - a maximum specific stiffness of 40 CPa/(g!cc) for any metallic material used in the engine - you are limited as what you can do. I know that an MMC material has been developed which is within the rules but

I don't think it is quite there yet." When did you first use aluminium-beryllium pistons in a race engine?

"After we used them in qualifying engines... I can't remember if they were first raced in '98 or '99..."

Did the aluminium-beryllium liner come at the same time as the aluminium-beryllium piston?
"No - that was a separate development. It came earlier than the piston." Did that liner improve engine efficiency, due to its heat dissipation characteristics?
"Not noticeably. But - according to your design - you could get a 35-40% gain in terms of weight

reduction from the liners. An aluminium beryllium liner could weigh as little as 200 grams." When we spoke in 1997, you were starting to look at aluminium-beryllium and at that time you remarked that you were concerned at the cost implication of the material. Was it as expensive as you had anticipated?

"No. With hindsight I can say that it was very cheap! Cheap because the amount you used was less than I had anticipated and the parts lasted longer - their durability was better and the number of rebuilds you had to make was fewer.
So overall, I would say that it was a very

cheap solution."
"-
The initial altJminium-beryllium pistons used in

Formula One were machined from solid but I

know that Perfect Bore came up with a means of casting aluminium-beryllium pistons. Did you ever used cast ones?
"No. We machined in house from solid. We

could recycle the surplus material." Presumably you needed special technology to machine the material from solid?

"Yes, but I don't want to go into details there.
Obviously, it is not as easy to machine as a piece of aluminium. Quite a bit of hard work went into making it happen..." There was a lot of controversy over the health aspect of aluminium-beryllium as its dust is potentially poisonous.

"1 think that controversy was purely a political thing. With the right safety precautions that was not an issue. You had to make the right investment, then there was no problem. The real problem of this material was the 'haves' and the 'have nots' ..."

Ferrari was initially a 'have not'.
"Exactly!"

With aluminium-beryllium now outlawed, what are you using for the 2001 liners?
"They are Nikasil aluminium liners." Presumably the piston - now in the new aluminium alloy - is still a two ring, short skirt design?

"Yes."

End of Quote.

Paul Lamar

The Rotary Engine free News Letter. Powered by Linux.
If you want off the list PLEASE let me know and I will
remove  you.  ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2016 All world wide rights reserved.