Subject: PT6 verses the Wankel
From: "rotaryeng@earthlink.net" <rotaryeng@earthlink.net>
Date: 5/5/2016, 12:45 PM
To: A10-me-earthlink


Can't wait for the PT6 comparison, Rotary  comparison, We run a
PT6-27 in the Turbo Beaver,  CF-OES

Steve Carlisle

What is the fuel  burn Steve? What HP level do you cruise it at ?

Some of  the data I have is 650 HP for five minutes and 500 HP
continuous. 227 US gallons with a range 767 statue miles.  That  is
3.38 miles per gallon.

Max cruise speed  is 202 MPH. So 767 miles by 3.79 hours. 227
divided by 3.38  is  60 gallons an hour.  Diesel fuel is about 7
pounds per gallon or 420 pounds of fuel per hour.  That  translate
to a BSFC of  420 divided by 500 HP or .84  BSFC.

http://www.wipaire.com/myaircraft/dehavilland/DHC2_MK1/modifications.php#bos
sbeaver

A  turbo 3 rotor could make 500 HP all day long with a worst case BSFC
(full rich, not leaned) of .65 BSFC. Leaned it is .47  BSFC or about
half the fuel burn of a PT6.. A turbo compound  version would drop
the fuel burn to below  .4.

The turbo 3 rotor wins hands.  The cost of a PT6  is well above
$200,000 as I recall. One can build a lot of  turbo 3 rotors with
stock Mazda rotor housings and stock Mazda  rotors for $200,000. The
weight is likely to be half of   the weight of a PT6. The turbo is
off the shelf as is the  necessary oil and water pumps.  A PT6 gear
box could be  used.

However the 3 rotor is not certified (yet) so you  cannot take paid
passengers.

BTW My son,  James Paul Lamar, has lots of hours in twin otter's
with  PT6's. What is your fuel burn JP?

Paul  Lamar

Paul, I just get to play with it every once in a  while. It is
"thirsty" as they say. No matter how heavy it  gets loaded, it just
laugh's !!! The turbine in it now as  installed about a year ago,
Canada Surplus accidentally listed  3 for auction, I think it was
purchased for 230 thousand, CDN.  Apparently wrong stickers and the
pencil pushers sold them  off, OOPPPPPS ! The Rotary project is
exciting.

Steve  Carlisle

We have a Czech copy  in  the hangar but it is non certified.
Experimental aircraft only. I  think the crop dusters may have
protested the FAA and got it approved for  use on crop dusting
aircraft. I am not sure about that. It is a good and  reliable engine.


The Mazda Wankel in four rotor form and ceramic  apex seals
would give it a real run for the money. Some engine  manufacturer
needs to wake up and get it certified. Mistral almost did it  but
were hungup by by Mistrail's insisting on EFI. The FAA does
not like  EFI as it is too hard for them to read the source code
and figure out what  happens when. Mistrial should have used
an aircraft carburettor. Something  the FAA understands.
Lycoming has been trying for years to get EFI  certified.

Paul Lamar

What is the cost range of a hot section  inspection and overhaul for the
650HP PT6?

Dale  Davies


Although not a real (high pressure) fuel injection system, Bendix "Dribble"
fuel injection has been certified on Continentals for many
years.............Lynn E. Hanover

I don't think that is EFI. It is purely mechanical. The FAA has no
problem with that.

There are several certified mechanical fuel injection systems for aircraft
engines.

We think we can start the TTC engine next week for the first time.

That does not mean it will be the only time we run it before
we try to fly it.

Paul Lamar


The Rotary Engine free News Letter. Powered by  Linux. If you want
off the list PLEASE let me know and I will  remove  you.  ACRE NL
web site.  http://www.rotaryeng.net You Tube
http://tinyurl.com/beqqxas  Copyright 1998-2016 All world wide
rights  reserved.