Subject: PT6 verses the Wankel
From: "rotaryeng@earthlink.net" <rotaryeng@earthlink.net>
Date: 5/5/2016, 2:32 PM
To: A10-me-earthlink


 Can't wait for the PT6 comparison, Rotary  comparison, We run a
 PT6-27 in the Turbo Beaver,  CF-OES

 Steve Carlisle

 What is the fuel  burn Steve? What HP level do you cruise it at ?

 Some of  the data I have is 650 HP for five minutes and 500 HP
 continuous. 227 US gallons with a range 767 statue miles.  That  is
 3.38 miles per gallon.

 Max cruise speed  is 202 MPH. So 767 miles by 3.79 hours. 227
 divided by 3.38  is  60 gallons an hour.  Diesel fuel is about 7
 pounds per gallon or 420 pounds of fuel per hour.  That  translate to
 a BSFC of 420 divided by 500 HP or .84  BSFC.


 http://www.wipaire.com/myaircraft/dehavilland/DHC2_MK1/modifications.php#bos



sbeaver

 A  turbo 3 rotor could make 500 HP all day long with a worst case
 BSFC (full rich, not leaned) of .65 BSFC. Leaned it is .47  BSFC or
 about half the fuel burn of a PT6.. A turbo compound  version would
 drop the fuel burn to below  .4.

 The turbo 3 rotor wins hands.  The cost of a PT6  is well above
 $200,000 as I recall. One can build a lot of  turbo 3 rotors with
 stock Mazda rotor housings and stock Mazda  rotors for $200,000. The
  weight is likely to be half of   the weight of a PT6. The turbo is
 off the shelf as is the  necessary oil and water pumps.  A PT6 gear
 box could be  used.

 However the 3 rotor is not certified (yet) so you  cannot take paid
 passengers.

 BTW My son,  James Paul Lamar, has lots of hours in twin otter's
 with PT6's. What is your fuel burn JP?

 Paul  Lamar

 Paul, I just get to play with it every once in a  while. It is
 "thirsty" as they say. No matter how heavy it  gets loaded, it just
 laugh's !!! The turbine in it now as  installed about a year ago,
 Canada Surplus accidentally listed  3 for auction, I think it was
 purchased for 230 thousand, CDN.  Apparently wrong stickers and the
 pencil pushers sold them  off, OOPPPPPS ! The Rotary project is
 exciting.

 Steve  Carlisle

 We have a Czech copy  in  the hangar but it is non certified.
 Experimental aircraft only. I  think the crop dusters may have
 protested the FAA and got it approved for  use on crop dusting
 aircraft. I am not sure about that. It is a good and  reliable
 engine.


 The Mazda Wankel in four rotor form and ceramic  apex seals would
 give it a real run for the money. Some engine  manufacturer needs to
 wake up and get it certified. Mistral almost did it  but were hungup
 by by Mistrail's insisting on EFI. The FAA does not like  EFI as it
 is too hard for them to read the source code and figure out what
 happens when. Mistrial should have used an aircraft carburettor.
 Something  the FAA understands. Lycoming has been trying for years
 to get EFI  certified.

 Paul Lamar

 What is the cost range of a hot section  inspection and overhaul for
 the 650HP PT6?

 Dale  Davies


 Although not a real (high pressure) fuel injection system, Bendix
 "Dribble" fuel injection has been certified on Continentals for many
  years.............Lynn E. Hanover

 I don't think that is EFI. It is purely mechanical. The FAA has no
 problem with that.

 There are several certified mechanical fuel injection systems for
 aircraft engines.

 We think we can start the TTC engine next week for the first time.

 That does not mean it will be the only time we run it before we try
 to fly it.


 Paul Lamar


Paul,
You guys are running a regular Motec EMS right? That would be port injected
correct? Or are you running an injector body before the turbo?
Bill J.

Yes port injected.
It is p-port so there are  two injectors per runner.
That make a total of four injectors. One injector on the
ends of each of the AN hose's shown.

Paul Lamar


 The Rotary Engine free News Letter. Powered by  Linux. If you want
 off the list PLEASE let me know and I will  remove  you.  ACRE NL
 web site.  http://www.rotaryeng.net You Tube
 http://tinyurl.com/beqqxas Copyright 1998-2016 All world wide rights
 reserved.