Subject: PT6 verses the Wankel
From: "rotaryeng@earthlink.net" <rotaryeng@earthlink.net>
Date: 5/5/2016, 5:23 PM
To: A10-me-earthlink


Can't wait for the PT6 comparison, Rotary  comparison, We run a
PT6-27 in the Turbo Beaver,  CF-OES

Steve Carlisle

What is the fuel  burn Steve? What HP level do you cruise it at ?

Some of  the data I have is 650 HP for five minutes and 500 HP
continuous. 227 US gallons with a range 767 statue miles.  That  is
3.38 miles per gallon.

Max cruise speed  is 202 MPH. So 767 miles by 3.79 hours. 227 divided
by 3.38  is  60 gallons an hour.  Diesel fuel is about 7 pounds per
gallon or 420 pounds of fuel per hour.  That  translate to a BSFC of
420 divided by 500 HP or .84  BSFC.


http://www.wipaire.com/myaircraft/dehavilland/DHC2_MK1/modifications.php#bossbeaver

A  turbo 3 rotor could make 500 HP all day long with a worst case
BSFC (full rich, not leaned) of .65 BSFC. Leaned it is .47  BSFC or
about half the fuel burn of a PT6.. A turbo compound  version would
drop the fuel burn to below  .4.

The turbo 3 rotor wins hands.  The cost of a PT6  is well above
$200,000 as I recall. One can build a lot of  turbo 3 rotors with
stock Mazda rotor housings and stock Mazda  rotors for $200,000. The
weight is likely to be half of   the weight of a PT6. The turbo is
off the shelf as is the  necessary oil and water pumps.  A PT6 gear
box could be  used.

However the 3 rotor is not certified (yet) so you  cannot take paid
passengers.

BTW My son,  James Paul Lamar, has lots of hours in twin otter's with
PT6's. What is your fuel burn JP?

Paul  Lamar

Paul, I just get to play with it every once in a  while. It is
"thirsty" as they say. No matter how heavy it  gets loaded, it just
laugh's !!! The turbine in it now as  installed about a year ago,
Canada Surplus accidentally listed  3 for auction, I think it was
purchased for 230 thousand, CDN.  Apparently wrong stickers and the
pencil pushers sold them  off, OOPPPPPS ! The Rotary project is
exciting.

Steve  Carlisle

We have a Czech copy  in  the hangar but it is non certified.
Experimental aircraft only. I  think the crop dusters may have
protested the FAA and got it approved for  use on crop dusting
aircraft. I am not sure about that. It is a good and  reliable
engine.


The Mazda Wankel in four rotor form and ceramic  apex seals would
give it a real run for the money. Some engine  manufacturer needs to
wake up and get it certified. Mistral almost did it  but were hungup
by by Mistrail's insisting on EFI. The FAA does not like  EFI as it
is too hard for them to read the source code and figure out what
happens when. Mistrial should have used an aircraft carburettor.
Something  the FAA understands. Lycoming has been trying for years to
get EFI  certified.

Paul Lamar

What is the cost range of a hot section  inspection and overhaul for
the 650HP PT6?

Dale  Davies


Although not a real (high pressure) fuel injection system, Bendix
"Dribble" fuel injection has been certified on Continentals for many
years.............Lynn E. Hanover

I don't think that is EFI. It is purely mechanical. The FAA has no
problem with that.

There are several certified mechanical fuel injection systems for
aircraft engines.

We think we can start the TTC engine next week for the first time.

That does not mean it will be the only time we run it before we try
to fly it.


Paul Lamar


Paul, You guys are running a regular Motec EMS right? That would be
port injected correct? Or are you running an injector body before the
turbo? Bill J.

Yes port injected. It is p-port so there are  two injectors per
runner. That make a total of four injectors. One injector on the ends
of each of the AN hose's shown.


Paul Lamar


Paul,
I wondered what kind of pump you would be running. (Fuel) Since you are
port injected you would only need normal injector pressure, (around 50-60
psi) plus enough to overcome the turbo boost pressure. Are the injectors
Motec wants standard solenoid or pezio? I'm looking for an EMS for a 3
rotor and I was thinking Motec or SDSEFI.
Bill Jepson

We are running a mechanical pump off the dry sump pump shaft :-)
there is also an electrical boost pump to get it started.

The injectors look like ordinary automotive injectors. I don't know
the brand.

Learn to program a Maximite and do your own. You will be WAY ahead
of the problem as you will know what does what when. You will save
a lot of money in the bargain. You all also gain a very valuable
skill in today’s automation manufacturing environment.

I am thinking of doing one myself as soon as we get done with
the TTC project. I will post everything including the BASIC source.

Paul Lamar

  The Rotary Engine free News Letter. Powered by  Linux. If you want
off the list PLEASE let me know and I will  remove  you.  ACRE NL web
site.  http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
Copyright 1998-2016 All world wide rights reserved.