Subject: double the RPM double the HP.
From: "rotaryeng@earthlink.net" <rotaryeng@earthlink.net>
Date: 5/5/2016, 6:21 PM
To: A10-me-earthlink


I found this excerpt in a book I had called V10 Formula One
Technology by Ian Bamsey.

If we made rotors out of Beryllium Aluminium alloy it would reduce
the rotor weight to 2.1 pounds from 9 pounds currently roughly. That
would double the RPM as the limit is controlled by the rotor bearing
load.

Beryllium Aluminium is they only light material that will withstand
the heat of a rotor.

Quote:.

And this coming season the peak power speed will be over 18,000?

"We are always trying to increase it but for 2001 we have got a
regulation change - the new materials limitation."

When we spoke in 1997 you were still using pistons made from the
traditional RR58 aluminium alloy. At the time, nobody seemed to have
a better alternative. Using RR58, piston cooling was an issue so you
had an oil spray to the underside of the crown. Was cooling still an
issue with the lightweight, relatively high heat rejection,
aluminium-beryllium pistons you have used over the last couple of
years? "Yes - they still contain aluminium and the issue is still
there!"

How significant was the introduction of the aluminium-beryllium
piston? "The properties of the material had certain benefits, no
question. But it also posed problems, including machining problems.
It was a step. With the change in regulations which outlaws this
material for 2001 we have had to do quite a lot of work in developing
an alternative." Is your alternative an MMC material? "No, it is an
aluminium alloy. With the regulations as they are now - a maximum
specific stiffness of 40 CPa/(g!cc) for any metallic material used in
the engine - you are limited as what you can do. I know that an MMC
material has been developed which is within the rules but

I don't think it is quite there yet." When did you first use
aluminium-beryllium pistons in a race engine?

"After we used them in qualifying engines... I can't remember if
they were first raced in '98 or '99..."

Did the aluminium-beryllium liner come at the same time as the
aluminium-beryllium piston? "No - that was a separate development. It
came earlier than the piston." Did that liner improve engine
efficiency, due to its heat dissipation characteristics? "Not
noticeably. But - according to your design - you could get a 35-40%
gain in terms of weight

reduction from the liners. An aluminium beryllium liner could weigh
as little as 200 grams." When we spoke in 1997, you were starting to
look at aluminium-beryllium and at that time you remarked that you
were concerned at the cost implication of the material. Was it as
expensive as you had anticipated?

"No. With hindsight I can say that it was very cheap! Cheap because
the amount you used was less than I had anticipated and the parts
lasted longer - their durability was better and the number of
rebuilds you had to make was fewer. So overall, I would say that it
was a very

cheap solution." "- The initial altJminium-beryllium pistons used in

Formula One were machined from solid but I

know that Perfect Bore came up with a means of casting
aluminium-beryllium pistons. Did you ever used cast ones? "No. We
machined in house from solid. We

could recycle the surplus material." Presumably you needed special
technology to machine the material from solid?

"Yes, but I don't want to go into details there. Obviously, it is not
as easy to machine as a piece of aluminium. Quite a bit of hard work
went into making it happen..." There was a lot of controversy over
the health aspect of aluminium-beryllium as its dust is potentially
poisonous.

"1 think that controversy was purely a political thing. With the
right safety precautions that was not an issue. You had to make the
right investment, then there was no problem. The real problem of this
material was the 'haves' and the 'have nots' ..."

Ferrari was initially a 'have not'. "Exactly!"

With aluminium-beryllium now outlawed, what are you using for the
2001 liners? "They are Nikasil aluminium liners." Presumably the
piston - now in the new aluminium alloy - is still a two ring, short
skirt design?

"Yes."

End of Quote.

Paul Lamar



Make the rotors out of Titanium.  It's a lot lighter than cast iron and
doesn't have the heat issues that aluminum does.

 Mark LaPierre

The Rotary Engine free News Letter. Powered by Linux.
If you want off the list PLEASE let me know and I will
remove  you.  ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2016 All world wide rights reserved.