Subject: TTC engine starts right up. Correction.
From: paul lamar
Date: 5/17/2016, 7:43 AM
To: A10-Me-Earthlink



The next run is today at 2PM

The rough running is normal with a p-port. P-ports have a lot of
valve overlap at speeds less than 4500 RPM.

The smoke was probably caused by no restriction in the oil feed to
the TC bearing. The oil pressure was 130 PSI.

My mistake.

Consensus from friends say there should be a .040" dia. restrict-or
in there. So I made one on the lathe and put it in the fitting on top
of the turbo charger bearing unit.

That should cut most of the smoke.

It has twice the power to weight ratio and half the size as the PT6
powered Legend and that will climb at 6,500 feet per minute.

From that point of view ours should climb at 13,000 feet per minute
easily beating the Bear Cat record of 10,000 feet in a minute and a
half.

Here is a screen shot of the Motec EFI Data log. The Motec EFI
records the data at 10 records per second. Think of it as a airline
black box.

The curious thing is the intake air temperature actually went down as
the engine ran just above idle at 2300 RPM. Prop RPM was 760.

The next test will be a full power run well tied down on the back of
a flat bed tow truck at 45 degrees angle of attack to check all the
pump functions.

The video is low rez that is the only way to get the file size down
to email.

Here is the PT6 Legend taking off.

Paul Lamar

Valve overlap????????

Your videos don’t open for me. What format are you sending? Thanks.
John Dinkel

That is because you are using an Apple John. Probably an old Apple
:-)

Here is todays run. We got it up to 3200 RPM. No smoke.

We cleaned the normal plugs and it started on the first blade. Just
like my RX8 does.

Next step is put the wings on and run it at full power.

This engine is half the weight and size of a PT6 engine so it will
fit in a much smaller airplane that is half the weight of a PT6
powered airplane.



Paul Lamar


Paul, Great job! Looking forward to seeing it flying. Pretty exciting
project.

Ray Hellstrom


Thanks Ray.

This has wide spread implications in the aircraft engine
manufacturing community. The question is how long is it going to take
before the market wakes up. Perhaps the time to climb record will
help. As we are getting experience with this engine I am getting the
impression a Reno racer version would not be all that hard to do.

Paul Lamar


Paul,  It sounds like some extra  caution may be in order today for you to avoid having to answer FAA inquiries about a flying flat bed tow truck. I love that you are doing the work to push the boundaries.  Good luck this afternoon.

Now, when you have time to be contemplative, see if you can give me some reaction to this. Your 13,000 foot/minute rate of climb might beat that of the Bearcat and wake up the industry to the benefits of the Wankel.

But, from the viewpoint of market acceptance I'd like to hear that your thinking might include keeping the benefit of your power/weight ratio in a very small and light engine scaled down in diameter to produce about 300 hp.

Would not the slimmer design lighten the centrifugal load on main bearings and produce better heat dissipation?  I suppose what I'm suggesting would require a complete redesign...a new engine.  And, I suppose the Mazda folks have been all through that.  But, the needs of young general aviation folks would be best served by the smaller but high producing engine.  Do you see anything like that coming? Dave.

David Meier

Not at all. This is a stock Mazda 132B engine mostly. The amount of power it puts out
is strictly a function of the boost. The RPM pretty much is the same at all power
levels. That is dictated by the gear box ratio and prop diameter.

If you need a LSA engine a one rotor version with out the turbo would work.

Paul Lamar


The Rotary Engine free News Letter. Powered by Linux. If you want
off the list PLEASE let me know and I will remove you. ACRE NL web
site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
Copyright 1998-2016 All world wide rights reserved.