Subject: Re: Converting charge cooling to oil cooling.
From: paul lamar
Date: 5/20/2016, 3:45 PM
To: Chris Hoskins

private

an entirely different situation.


run a carbide reamer or drill through them and
the problem (if it exist) goes away

It is just the surface finish in the hole.

The bolt that we put in them takes most of the
load anyway.


Paul


On 05/20/2016 03:21 PM, Chris Hoskins wrote:
Hi paul,
    Reading that article by Brad Chubb, do you think that those holes we
had EDM'd through the planet shafts will affect us in the same way ?
        Cheers Chris.

-----Original Message-----
From: paul lamar [mailto:rotaryeng@earthlink.net]
Sent: Saturday, 21 May 2016 8:12 a.m.
To: A10-Me-Earthlink
Subject: Converting charge cooling to oil cooling.




Hi Paul: Although my project has been stalled for several years, I still
plan on pursuing using the over 40 of the OMC single-rotor engines I have
that were in the Evinrude/Johnson snowmobiles in the 1970's.

I know, you're not crazy about charge-cooled rotaries, but I see an
opportunity to gently use them w/out demanding all the horses they can
produce. I felt, in my very-amateur opinion, that Eric Barger was too
optimistic w/ the power he would be getting from his ROTORMAX line of
rotaries.

So, I've been paying attention to your ideas of using set screws instead of
a bolt all the way through the eccentric shaft as Tracy C. did.

The idea is to couple two (possibly more) together to produce 70-90 hp
(OMC's first ones were rated @ 35 hp @ 5,500 rpms, and then later, 45 hp @
6,500 rpms) for flying purposes. I chose the OMCs for several reasons.
The main reason was after talking w/ one of their engineers over the phone
that was retired in the Chicago area many years after OMC shut down. He said
those engines were well-built, and weren't really being taxed too hard in
snowmobile use.

Severe back problems (partially caused by jerking around one of the OMC
engines that had seized after I foolishly revved it to over 8K rpms w/out a
load on it) & working too many hours are my excuses. Now recently retired,
the back problems are mostly a thing of the past, but on limited funds,
unlike before.

Before I retired, I was able to acquire those OMC engines, as well as donate
that $500 toward your TC project, when I had extra funds! Still plan on
donating some funds for each OMC engine sold in the future to
your(?) Everett Hatch fund.

Also, have acquired one of the Aixro-50 engines to attempt an ultralight
gyroplane, too.

A big distraction after back problems have greatly diminished has been
switching over from a Rotax 503 (52 hp) to one of the Yamaha three
cylinder,120 hp, four-stroke snowmobile engines on my Sport Copter gyro.

I've trailered it out-of-state several times to El Mirage dry lake bed,
Santa Maria, & Yreka in CA, to Yuma, AZ, Brigham City, UT, and Mentone, IN,
for gyro flying at events in those locations. Also many times to Alvord
desert dry lake bed in far SE Oregon. Love that Yamaha power!

Hope to love the smoothness of rotary power flying a gyro in the future.
Have acquired three different gearboxes to work w/ the OMCs. Had a machinist
cut a Rotax taper into one of the eccentric shafts to use w/ one of the
Rotax drive gears for an "A" gearbox (2.58:1 reduction). He said the
hardening treatment OMC put on that ecc. shaft was a killer to overcome,
dulling three of his cutters!

Kevin Richey
Portland, OR


If you don't mind a visit I am planing on being in Portland shortly. I would
like to look at those engines and take a few photos if you don't mind.

I have an idea based on some of what we have learned on the TTC engine of
converting a charged cooled engine  to oil cooled. We drill a hole in the
E-shaft and feed high pressure oil in from one end using an off the shelf
Barns dry sump pump. Then we drill a holes to feed the plain rotor and main
bearings. It can be made plain by installing a simple bushing where the
roller bearing was, Next we drill and oil squirter hole to cool the rotor.
Then the Barnes can be used to scavenge the oil with out installing an oil
pan.

The hardness of the shaft is not a problem because once you get through the
hard shell it become softer in the center. Modern carbide drills will do the
trick. If that does not work we can heat them locally and normalize them in
that small area .
We can re harden them later if necessary.


Paul Lamar

Also one can use EDM to drill holes in hard steel. This opens up a bunch of
possibilities perhaps we can modify an AIXRO to make it oil cooled. The TTC
engine also opened my eyes to other possibilities. Once you have an external
oil pump and scavenge pumps a myriad of Wankel configurations are possible.


Paul Lamar


Squirting oil into the rotor to cool is sounds good, getting rid of the ball
bearing
    and using a sleeve bearing and then supplying it with oil also great.

How do you get the oil out of the rotor? With it spinning wouldn't
centripetal forces sling the oil into the rotor?  How would you evacuate the
oil from around the e-shaft and the inside of the rotor?

I have several charge cooled wrankels I would luv to convert to oil cooled
too.

David Mikesell

What kind do you have David?

Paul Lamar


The mention of EDMing in hardened steel reminds me of an issue from a
previous life that provides a precautionary message to share.

In one of my previous jobs we EDMed small tight tolerance shearing cutters
out of hardened steel to cut leads off of electrical components as part of
an automated circuit board assembly process machine. The overriding cutter
required a "neck" to pass over the under riding cutter and still fit within
the under board adjacent component clearance envelope. We had to EDM the
cutters out of hardened material because if we tried to fabricate with more
traditional machining methods and then harden the cutters they would distort
out of tolerance and not shear the leads effectively. That all seemed fine
and we thought we had a process to produce parts from. However we were
seeing premature failure of the overriding cutter in the neck area.
Structural analysis and FEA analysis indicated we should have had ample
margin.

After a great deal of investigation and engineering analysis we came to
realize that the EDM process was creating a microscopic annealed layer all
the way around the profile of the cutter. Not only that but the soft layer's
surface had a roughness on a microscopic level across the grain of the
material. That roughness created stress concentration points at which micro
cracks would start. These would grow and eventually propagate into the
hardened material at which point the cutter failed (sudden brittle fracture
of the hardened material). We solved this by EDMing a few thousandths
oversize and then grinding the profile with the grain of the material to the
final dimensions to remove the annealed zone.

Certainly EDMing is a very valuable fabricating method with many advantages
and benefits. But please pardon me for providing a point that may be
understood by any or all of those who read this in that we need to realize
the potential for EDM to adversely affect the surface hardness of hardened
materials.

Hope that helps someone avoid a problem I had to figure out the hard way.

Regards,
Brad Chubb


We are putting small holes in a large low stress part. I doubt this will
cause any problems. Also a carbide drill a slight bit larger would clean the
surface of the hole.

Paul Lamar

The Rotary Engine free News Letter. Powered by Linux. If you want off the
list PLEASE let me know and I will remove  you.  ACRE NL web site.
http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas Copyright
1998-2016 All world wide rights reserved.


---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus