Kevin Richey actually has 40 of these engines.
In theory it is possible to convert them from charge cooled to oil
cooled. I can show you how.
Kevin is interested in selling a few. Kevin is in the Portland area.
Paul Lamar
Kevin,
Please advise OMC Rotary engines:
Power Output/RPM,
Fuel Type & Burn Rate,
Spare Parts Availability and
Engines & Spare Parts Pricing ?
Are you converting units to Oil Cooling?
If so, Pricing?
THANKS,
Frank Parker
****************************************************
(Lengthy) Frank: Answering your questions:
1. (Power output/rpm): OMC initially rated these single rotor engines in
late 1972 @ 35 hp @ 5,500 rpms. They were sold in the Evinrude & Johnson
snowmobiles. Shortly afterwards, they enlarged the intake & exhaust
ports slightly & raised the hp rating to 45 horses @ 6,500 rpms. Chamber
volume is 528cc.
2. (Fuel type & burn rate): Regular gasoline is all they need to produce
the power. Some companies pursued using alternate fuels in the rotary,
including Mazda. Various fuels have been experimented with, such as
Jet-A, diesel, natural gas, & propane.
One fella (I don't have any info as to who, where, when) in England
years back supposedly got his Mazda to run fine on diesel by first
starting it on gasoline, then switching to diesel in a carb-engine. I
suppose I shouldn't have mentioned that, since I don't any direct
knowledge of the facts...
I do not have any burn rate...but, it's a rotary. Power in a small
package requires fuel comparable to the power output of piston engines.
3. (Spare parts availability): OMC left the snowmobile business in the
1970's. Occasionally their rotary-engined sleds pop up on ebay, which is
where I acquired the majority of these engines. I have about 40 engines
in good shape (freely turn, and have compression. The apex seals spring
back when depressed through the exhaust port).
Many of these engines have the electric starter. About half have the
axial fan & associated housings OMC built them with. I planned to remove
those & use a regular automotive radiator fan on the non-PTO end, the
same as OMC did. Possibly add smaller fans around the minor axis (spark
plug & exhaust portion).
I have another 6-7 that are seized, for parts. They usually seized up
from the high-speed throttle valve being sucked into the rotor housing
w/ predictable results (foreign metal parts became wedged between the
apex seals & the housings, gouging the walls. The apex seals usually did
not suffer any damage, nor did the rotor, being cast iron.
Guys found removing that HSTV created no difference in the engine's
power. There is a web page showing to do so that I'll find the link to.
There is a fellow in Michigan that runs a sled salvage/parts house.
Dave's OMC Warehouse. I would advise caution in dealing w/ him.
Complaints against him on the internet from customers include sending $$
& not hearing from him for months at a time, as well as almost a total
lack of communication from him.
When I inquired of him re: parts, I found he thinks they are made of gold.
The OMC apex seals are between the Mazda 10A & 12A in dimensions. I
thought I'd have a machinist turn the 12A seals down slightly to have
spare ones. Apparently, Rotamax did so for their line of these engines.
4. (Engines & spare parts pricing): I am also interested in selling what
parts are good shape from those 6-7 seized engines, such as rotors &
eccentric shafts (which have the reputation of being pretty much
bullet-proof).
Also, any side housings that escaped the wrath of foreign metal bits
being flung around inside the housing. Those gouged rotor housings &
side housings would be free to anyone who wanted to experiment w/
re-conditioning them. Sometimes the needle rotor bearings gave up the
ghost, also.
I'm willing to sell the good engines for $795 apiece (for list
members...just mention you're one of Paul's subscribers), w/ a portion
of the sales of each one going to Paul Lamar for his ROTARY ENGINE.NET
<
http://ENGINE.NET to apply wherever he sees fit (he didn't know of this
until now!).
Paul has provided all of us a wealth of information as well as a forum
for world-wide fans of Felix Wankel's wonderful invention. He has
incurred expenses for all of his research that I doubt anyone else has
come close to.
These are only the ones that I know
about:The Everett Hatch memorial
fund for air rotary racing contests, motor mounts, slide throttle,
compound turbo, & the upcoming time-to-climb event.
My opinion here: I believe we all should donate to all that has been
incurred in Paul's expenses. I had previously done so to support the
compound turbo project. I don't say this to seek recognition, but to
encourage others to help defray Paul's costs.
I plan on selling the majority of these rotaries on ebay (for a higher
price), after RE.net list members have first choice.
My plans for these OMC rotaries revolved around combining two together
for flying purposes (for light aircraft, and for my gyro flying),
because I think Rotax prices are too high. I first discovered the
possibility of doing so when I read of three guys doing so in snowmobile
racing in the unlimited class in Minnesota.
They stated that w/ the mods they did, they estimated they got 112 hp
from the two engines coupled together. No dyno was used for that power,
but seat-of-the-pants guess-timate from their racing experiences. They
enlarged the ports, removed the axial cooling fans, and the flywheels,
electric starter, and used a Harley ignition, since the flywheel
contained the stock ignition.
By setting the two rotors 180 degrees apart, the engines were balanced,
since they didn't need the flywheel. They rotated the exhaust port down
into the snow & ice surface to cool the external fins OMC cast into the
housings. The ice cold water created clouds of steam, making spectators
think the engine was going to blow, they said!
I chose the OMC rotaries because they have much more hp than any of the
Fichtal-Sach ones used in the snowmobiles by Arctic Cat, and the Savkel
rotaries that were made in Israel. Mazda rotaries are too heavy for
lighter aircraft.
I looked into purchasing one of Dave Atkin's single rotor offerings,
made from Mazda parts, but felt his pricing is like Rotax.
5. (Converting these OMC units to oil cooling): I do not have the
machining expertise nor equipment to do so, although I think Paul's idea
is great. Perhaps someone on this list is interested in running w/ it.
6. (If so (oil cooling), pricing): N/A
Sorry for the length of this reply, but I felt the info needed to be
stated. Rotary engine fans are always interested in all things rotary.
Felix Wankel is one of my heroes!
I got to talk on the phone years ago w/ one of the engineers who worked
for OMC during their rotary builds. I was seeking his advice regarding
my plans. OMC purchased a license from Curtis Wright in order to study &
then produce them. They made approximately 15,000 of these, and were
wildly successful in combining four in outboard racing.
He related how he had visited w/ Felix Wankel a couple of times as a
guest in his home in Germany. He told me of Felix taking him & others
out on the lake in his motorboat. He genuinely liked FW, while others
found him difficult to work w/.
I'm getting my gyroplane ready to take it to ROTR (Rotors Over The
Rockies) in Brigham City, Utah in about 10 days. Doing the annual now (I
know, wintertime is best for annuals). After I get back in Mid-June, I
can divert my attention to those who wish to obtain one or more of these
little gems. If anyone is disappointed in what they see after receiving
them from me, they can have their $$ back. Shipping not included.
Years of low-back pain problems delayed me proceeding prior to now. I've
retired, and realized I bit off more than I can handle when I acquired
all these OMCs to convert them for flying powerplants. I don't need
another job after working full-time for over 45 years.
Kevin Richey
Portland, OR
The Rotary Engine free News Letter. Powered by Linux. If you want
off the list PLEASE let me know and I will remove you. ACRE NL web
site.
http://www.rotaryeng.net You Tube
http://tinyurl.com/beqqxas
Copyright 1998-2016 All world wide rights reserved.