Subject: how to fix a charge cooled engine. CONCEPT
From: paul lamar
Date: 5/30/2016, 5:00 PM
To: A10-Me-Earthlink



 It occurred to me if you pump enough oil into the rotor roller
 bearing it will cool it. Normally a roller bearing requires very
 little oil and that is why they are used in charge cooled engines.
 The trouble is there is not enough oil flow to cool it at high power
 levels mixing small amounts of oil with the fuel.

 The engine will also need a scavenge pump to get the hot oil out and
 through a oil cooler and back into an oil tank.

 On the OMC all that is needed is one small hole in the back side of
 the eccentric lobe to feed high pressure cooling oil into the rotor
 roller bearing. High pressure cooling oil is fed into the eccentric
 shaft from one end or the other.

 There will also be a hole in the case just beyond one or both of the
 main bearings to suck the excess cooling oil back out. Some the of
 the fuel mixture will be sucked out as well but the fuel will go to
 the bottom of the oil tank and can be recovered.

 If the intake plumbing is changed so no mixture goes into the main
 bearings and through the rotor then no fuel will be sucked out with
 the cooling oil. In other words just a simple p-port is all that is
 required. In fact there will then be no mixture in the center of the
 engine at all.

 Here is a scavenge pump on ebay for $219. One section can be used as
 the pressure pump.

 This is A MAJOR DEVELOPMENT for charge cooled engine including the
 AIXRO if it works.


 Paul Lamar



 Paul, and Group, Roller, needle, and ball bearings have a requirement
 for light lubrication. Rollers especially. If over lubricated the
 rollers can hydroplane, or skip. The problem is when they touch back
 down. Think of a plane landing and how the tires often chirp as they
 match speed. The same thing can happen to a roller bearing with
 catastrophic results. The steel can weld together or chip causing
 bearing failure

 Bill Jepson.

 How does load and clearance factor in?

 The load on the rotor roller bearing is quite complex due to
 centrifugal force on the rollers varying as they make their way
 around the center of the e-shaft.

 It's a wonder they work at all. I think it is still worth a try.

 Paul Lamar

 All,

 I like the concept of using oil, fuel, air, or any fluid in different
 ways and volumes to cool PARTS of the engine.   Pumping higher volume
 of oil near a bearing might be enough to cool it even if not used for
 lubrication.  Making the supply channels for fluid crazy large, might
 help dissipate heat, or move it so cooler sections of the engine.

 Hollow rotor shafts come to mind.  Could centrifugal force help
 distribute fuel, air, oil, or water?

 Extra intake air channels or fuel passages could also help cool PARTS
 of the engine.  In the case of using fuel for cooling evaporation of
 fuel as it absorbs heat could atomize fuel pre-combustion.  Rocket
 engines sometimes cool the rocket nozzle with fuel on the way to
 combustion.  When the fuel runs out, their is no more heat produces,
 so the process is self limiting.

 Perhaps injecting the air/fuel charge into the next chamber, on each
 rotation, would move the heat of combustion to the next chamber..
 Yes, more exhaust pipes and intakes, and turbos, but more even heat
 distribution.

 Another possibility is to alternate only the intake and combustion
 chambers, therefore cooling the alternating combustion chambers. The
 former combustion chamber would heat air enough to get a little
 expansion.  Would this need to be a four or five lobed rotor?  Like I
 say, I know nothing.

 Ok, the extra plumbing may make the above ideas a problem

 But a turbo-electric generator could capture high rpm exhaust energy
 for electric power fed directly to an electric motor running at
 engine speed. Therefore no extra storage batteries needed.  The
 system would avoid a transmission for turbo compounding.  This is the
 simple, light way. Convert high rpm from a turbo into useful power.

 Parker May

Turbo-electric generators are used on current  Formula One engines to provide
turbo compounding. They call it energy harvesting. Currently Mercedes,
Renault, Ferrari, and Honda are building such engines. The new Mazda 350 HP RX9 will
probably have it.

This was the result of a lecture I gave on the TC subject in 2008 at the
World Motor Sport symposium in Oxford UK. The magazine article pdf is
attached.

This is the video:

http://www.rotaryeng.net/Oxford-TC-talk.mp4

Paul Lamar



 The Rotary Engine free News Letter. Powered by Linux. If you want off
 the list PLEASE let me know and I will remove you. ACRE NL web site.
 http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
 Copyright 1998-2016 All world wide rights reserved.