Subject: Reduce the heat loss to the coolant by half.
From: paul lamar
Date: 8/1/2016, 11:14 PM
To: A10-Me-Earthlink






On Aug 1, 2016 8:30 PM, "paul lamar" <rotaryeng@earthlink.net <mailto:rotaryeng@earthlink.net>> wrote:


    Double the thickness of the hard steel liner in the rotor housing.
    This will result in a large reduction in fuel burn. BSFC.

    A simple change that Mazda could do on the production line.


    Paul Lamar

    Hi Paul,
    How does a thicker liner give a reduced fuel burn; what is the theory here?

    Dave in Perth

    One wants to keep as much heat (temperature)  in the combustion chamber
    as possible.
    The steel liner acts as insulation as unusual as that sounds.
    The heat transfer rate of steel is much much lower than that of
    aluminum. So one would want to increase the thickness of that insulation
    to prevent the aluminum from carrying  away all the temperature.

    As the combustion chamber rotates toward the exhaust port it is exposed
    to new areas of the steel liner which are cooler and more and more
    temperature  is lost. When one cools off a high pressurized container
    the pressure is reduced in that container. This pressure is acting on
    the face of the rotor and that is what generates the torque so potential
    torque is lost.

    (P1 X V1) / T1 = (P2 X V2)/ T2

    Change any one of those terms in the first part and that  will change
    the second part.

    https://en.wikipedia.org/wiki/Gas_laws

    It is a fundamental law of physics.

    Note: in this attached chart stainless steel  is 1/3 that of cast iron.
    That is why Mazda
    needs to find out how to make the rotors out of SS instead of cast iron.
    SS would be good for the liner as well if it were possible to chrome
    plate it.

    Also note: In the heat transfer units it is

    watts / (meters X Temp)

    so the thicker material the less heat is transfered.

    Thermal details like this affect the BSFC of all engines.

    Hold a piece of steel on a grinding wheel with your bare hands.
    Then hold a piece of the same size SS and report back :-)

    Paul Lamar


    What is the heat transfer and cost of a ceramic coated rotor versus a
    stainless steel rotor?

    As temperatures increase of the combustion chamber and sliding surfaces,
    what is expected to be the next weak link?  I suspect carbon buildup
    would go down but will seal lubrication become an issue?

    Speaking of seal lubrication, which paper addresses why the apex seals
    aren't lubricated from inside the rotor?


    Aron Buster

    "What is the heat transfer and cost of a ceramic coated rotor versus a
    stainless steel rotor?"

    I have no idea. Who is doing ceramic coating on rotors? I would hesitate
    to use it because if some of it came off it would destroy the wear
    surface of an expensive rotor housing.

    The  proven Iannetti silicon nitride seals will tolerate double the
    temperature of an iron seal.
    I have never heard of one breaking up in 17 years of this news letter.
    They are
    solid silicon nitride with fiber reinforcement supposedly.

    The main function of the apex seal oil is cooling the iron apex seals.
    Synthetic oil will tolerate
    twice the temperature of organic oils. Turbine oils are better than that.

    If you use synthetic oil there is no carbon build up.

    "Speaking of seal lubrication, which paper addresses why the apex seals
    aren't lubricated from inside the rotor?"

    You got me there. Do you know if there is such a paper?
    It might work but the holes would have to be tiny and subject to
    plugging up if some one used organic oils.

    Also the amount of oil required is a function of horse power.
    I don't know how one would control that with out a computer.
    Mixing with the fuel already does that. More fuel, more oil, more power.


---------------------------------------------------------------------

    BTW the stock oil "injector pump" is not really a pump at all.
    It is an oil distribution device. The oil is transfered to the
    compression chamber when the chamber is lower pressure than atmospheric.
    The so-called injectors are open to the atmospheric pressure.

    If one turbo charges the RX7 engine less apex seal oil will find its way
    to the apex seals. Mazda themselves made that mistake when they turboed
    the rotary back in the late 80's and all of the 90's.
    If you have one of those you better be mixing oil with the fuel :-)

    Some people on the Internet get it wrong. They incorrectly assume the
    RX7 "pump" AKA OMP is fed from the high pressure oil system. Not true
    except possibly for the RX8. It is fed from a gravity fed atmospheric
    pressure oil reservoir. To prove it take the RX7 "pump" off and turn the
    engine over with the starter and see if oil squirts out of the supply hole.


    Paul Lamar


    Hi Paul

    I have looked quite a bit into ceramic coatings to act as thermal
    insulation layer and as part of that I have talked to several world
    experts on the subject matter

    There are actually quite a few options for applying thermal coatings
    onto metal surfaces and for the most part they can be applied to many
    materials even some some low temp materials. Most are applied with very
    high velocity impregnations. These nozzles are cnc programmed to apply a
    pattern to get complete coverage

    The issue is that I have not found any coaters who are able to guarantee
    that the coating thickness will be uniform across the surface being
    coated. This means than for the most part, the ceramic surface will need
    to be lapped post coating process. This would make this process coast
    prohibitive for low volume applications. Even for high volume
    applications, it will be fairly expensive process because the thermal
    insulating ceramics also tend to be extremely hard to to lap.

    With that said, if Mazda proceeds with releasing a new rotary, I am
    pretty confident that they will utilize some sort of ceramic insulating
    layer to help meet the more stringent regulations

    Regards
    Simon Saba

    Hi Simon,
    The rotor would only need to be coated on the three outer surfaces,
    wouldn't it ?
      would they actually need to be lapped ? doesn't only the apex seal
    contact the liner ?
    Chris Hoskins.


    Don't do it Chris. You won't even notice it as it will be less than 1%
    lower fuel burn.

    If a small part comes off you can kiss your engine good bye.

    Also make sure you have a good air filter.

    Paul Lamar


    Hi Chris,

    Paul is absolutely right
    You can coat on the opposite surface (ie external surfaces surrounding the chamber) and indeed you will not need to lap if on this surface instead of the internal surface. It will still add insulation, however, because of the excellent conductivity of the metal, the heat will conduct sideways (ie radially) on the side plates, and axially and rotationally on the housing. This will reduce the effectiveness of adding the insulation. Certainly there will be an improvement but very small relative to insulating the internal surfaces

    The most effective, but unfortunately most expensive, is to insulate the inside surfaces. On piston engines, there are several aftermarket services that will coat the piston top and the inside surface of the dome and it helps keep the heat inside by adding insulation and reflecting radiated heat back in the piston. It would be an interesting experiment for someone to coat the outer surfaces of the rotor and quantify the impact.

    Simon Saba

    As long as there is no possibility of it coming  off.

    A piston engine will tolerate more debris.

    GM patented a multi piece rotor.

    Paul Lamar

    Some piston engine manufacturers are coating cylinder walls with a ceramic for low wear. I think Ford is doing an aluminum V8 now.
    The 26B Lemans engine was ceremet coated to help BSFC and wear. I do not know what development issues they may have had with that process. Mazda must have had patents that describe the process. I believe the rotor house and the side housings were coated. I would be interested to know if they sprayed directly onto an aluminum housing or whether they modified the steel liner for the ceremet thickness.
    Dale Davies


    That was silicon carbide applied with a detonation gun. I guess you could call it ceramic.
    It must be diamond ground. A very expensive procedure. Mazda tried Nikasil and it was not
    as good as detonation coating. Works better on cylinders.


    The Ford may have been nikasil.

    Nikasil is a trademarked electro deposited lipo philic nickel matrix silicon carbide coating
    for engine components, mainly piston engine cylinder liners.

    Paul Lamar

Paul,
I have a question about the det gun coating. In the LeMans paper it appears that they coated the side plates AND the rotor housings. It would seen like they didn't even have the normal steel liner. That was for the fuel limited year. This would seem like the reverse of what you are discussing. Any ideas about that? Do you know if they used a steel liner, or did they coat the aluminum directly?

Bill Jepson

I think you are right. The heat loss is one of many factors. Combustion  likes a spherical camber.
A flat chamber puts the fire out. They attempted to improve the combustion in the trailing
flat chamber area with a 3rd spark plug. That probably out weighed any benefits from lower heat loss
with the steel  linear.

That is also before we discovered that one could tig weld a P- port. Mazda was sand casting p-port
rotor housing at the time for road racing so it was easy to make changes in the patterns. The steel lined
housing are high pressure die-castings. The steel liner rotor housing is made on an automated production line.

Who knows what the engineers were thinking .

If I were doing it today I would tig weld the p-ports and the 3rd plug on the production
housings and get the benefit of the lower heat loss.

If and when I get the ignition patent we are going to experiment with multiple sparks every
5 degrees or in an attempt  to burn all that unburnt fuel.

I have been thinking about this for a very long time.

http://www.rotaryeng.net/Why-CDI.html

Here is a new idea! Heat the trailing flat combustion area with an
electric heater buried in the rotor housing. Or duct some exhaust gases
up there to heat the area. Or use a heat pipe.

Paul Lamar

    The Rotary Engine free News Letter. Powered by Linux. If you want off
    the list PLEASE let me know and I will remove  you.  ACRE NL web
    site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
    Copyright 1998-2016 All world wide rights reserved.