Subject: TTC new turbo Motec Lap Top PC monitoring the engine
From: paul lamar
Date: 8/2/2016, 5:42 PM
To: A10-Me-Earthlink



    This is with the new turbo and everything seems to be working fine.
    The engine passed the compression checks with flying colors. The
    plugs look great and the water injector lowered the intake air
    temperature out of the compressor from 200 F to 140F.

    Sorry about the shaking around. I was filming over Niles shoulder
    while asking him questions.

    Here is the video in low rez.

    This will give you an idea of the capabilities of the  Motec EFI
    system. The PC lap top is connected to the M800 CPU with a 20 foot
    USB cable and a USB to CAN converter. That  $100 USB to CAN converter
    normally would not be necessary in a later version of the Motec.  A
    single USB cable would suffice.  This one is several years old.

    The dash unit is connected  to the PC with an Ethernet cable. This is
    all  a bit of a kludge and it all can be done with just one USB in
    theory.  Some of the data  is in the M800 and some is in the Dash
    Unit. It would be better if Motec put a 64 GIG SD card in the CPU
    like a $60 Maximite has.

    We plan to run it this coming week at a 45 degree angle of attack to
     check the fluid  suctions. This will be done on the back of a flat
    bed tow truck.

    After that we are going to take it out to the desert and fly it.

    Rolls Royce will be green with envy :-)

    Paul Lamar

http://www.ebay.com/itm/USB-to-CAN-Bus-USB-CAN-Converter-Adapter-with-USB-Cable-Support-64-bit-Win7-/122060716973


    Dave Klingler

    Thanks for the tip Dave. Unfortunately I cannot cut into the wiring
    harness as the aircraft is not mine. Perhaps if I could find a mating
    male version of this  round connector with female pins I could dope
    out the wiring.  It almost looks like a old PC keyboard connector.
    But unfortunately it is not.

    Paul Lamar

    That connector is a 5-pin XLR.

    It is pretty common in stage intercom systems.  It should be easy to locate at an electronic supply house.

    Lester Turner


    Thanks Lester. I will order one from digi key or Mouser.

    Paul Lamar

    Does Motec publish the pinouts for their connector, so you can adapt the adapter?
    It does look a little different from the XLR connectors I have around here.

    I did look around for the one you have, and I found it selling for $200-300
    around the net.

    Dave Klingler

    No pin outs on that.
    I think it may be more than just a connector. There are some IC's inside
    doing some data conversion. I won't know until I try an off the shelf
    CAN to USB. Here are some pictures of the inside.


    Paul Lamar


    I see an FTDI chip in there which suggests that it is a USB to serial converter.I would take a look at this device from Mouser. http://www.mouser.com/ProductDetail/FTDI/TTL-232R-3V3/?qs=Xb8IjHhkxj627GFcejHp0Q%3D%3D
    you should be able to wire that into the XLR connector if you can find one with the same mating connection to fit the Motec.

    These are still used to program code to Arduinos and for people doing there own bootloading. Modern versions of Motec already include the USB conversion on board I'm sure.

    Daniel Tyler

It is a first in first out buffer so the Motec M800 USB can talk to the PC USB asynchronously.
It is like email. You send a message to me and it is stored on my computer until
I read and delete it :-)

Here is the data sheet.

Paul Lamar

    The Rotary Engine free News Letter. Powered by Linux. If you want off
    the list PLEASE let me know and I will remove  you.  ACRE NL web
    site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
    Copyright 1998-2016 All world wide rights reserved.