Subject: Glass Goose Sea Hawker cooling systems.
From: paul lamar
Date: 8/12/2016, 8:31 AM
To: A10-Me-Earthlink



 The RX8 core is a good core to use as are Chrysler Doge pick up
 cores. Large frontal area with thin cores. The Dodge core is 20" by
 30" and is very very effective in a cross counter flow configuration
 on the TTC engine. Two cores back to back.

 Let's take the Dodge in a non cross flow config.

 20 by 30 is 900 square inches.

 We have learned more about this subject since Neil Ungar started
 flying and on the time to climb engine. Neil complained about over
 cooling. It appears we can reduce the intake area of the wedge
 diffuser to 15%, of the frontal area of the core, from the  20%
 recommended previously.

 In other words 15% of 600 square inches is  90 square inches. The
 core is 20 inches wide so the height of the 4.5 inches high and 20
 inches wide.

 Both Neil and the TTC  rads are directly in the prop blast so if
 that is not the case then you may note higher water temp when
 taxiing.

 Here is the dodge core on top with the diffuser underneath. Yet
 another 3D :-) It is far enough forward to give room for the intake
 manifold behind it. This leaves room underneath for and oil cooler.

 The exhaust out the back of the cabin may help to attach more air to
 the aft sides of the cabin. This is a problem that was addressed by
 vortex generators previously (or in addition).

 Paul Lamar


 Excellent recommendations, thank you!   I was thinking of having the
 radiators on the top/back (low pressure) of the upper cowling with a
 long K&L duct.  Your version may be easier.   I will play with some
 radiator models on the actual engine.  The smaller the rad size the
 easier it will be to fit.  20x30 will be a challenge.

 In this model,  it seems that two 20x30x1 counterflow radiators
 would give a total volume of 1200ci?   Is it correct that we need
 about 600ci for water cooling and 200ci for oil?   If so, I assume
 that using cross counterflow rads would each need to be about 1/2 the
 Dodge size as long as I have 600ci?

 My RX8 has twin oil coolers about 8x10x2.  The single RX7 oil cooler
 is about the same volume.  The latter should fit up front if the
 water cooler intake is a little higher.

 Has anyone used 3D printing to create their engine cowling?

 Scott Gettings

 Those volume numbers depend on the thickness of the core. Thinner
 core less cubic inches are required as thin cores are far more
 efficient for a given volume. Dodge were leading the way with other
 manufactures catching on.

 This is a cross counter flow rad for a Tango

 14" by 24" They are Dodge Neon cores.

 Some what more compact at higher cost to make. You also need a
 skilled tig welder.

 -------------------------------------------------------------------------


Scott,

 We should change the standard to square inches of frontal area
 because all the recent cores are around 5/8 to 3/4 inch thick
 including the RX8. Rad core frontal area is more correlated to
 cooling than volume.

 600 square inches frontal area for 250 HP single core. 2 x 300 square
 inches  for cross counter flow. Two Neon rads are about that. Maybe a
 bit more so they should handle a mild turbo charge.

 BTW have you considered a 8" prop extension to help the air stick to
 the cabin sides? You can lesson the angel at which they go back. If
 you go back at 7 degrees and then cut it off flat that will implement
 the Kamm effect. Same as the recent Preuses.


 Paul Lamar



 Hi Paul, I noticed during my re-search on the Glass Goose that the Icon A5
 also has issues back in the cabin sides. They have also used vortex
 generators in that area, on the test planes. The GG has the lower
 wing and the landing gear that also adds to the problems.

 Steve Steve Carlisle

Yes. It is a result of the side by side seating. That Icon is almost a scam.
Be wary?

With the Glass Goose it would not be that hard to change it to side by side
and narrow the cabin. That lower wing is necessary to keep the prop out
of the water spray which will destroy it.

Here are a couple of great books on seaplanes. Extensive discussion
of the unique design issues.

Paul Lamar


 The Rotary Engine free News Letter. Powered by Linux. If you want
 off the list PLEASE let me know and I will remove  you.  ACRE NL web
 site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
 Copyright 1998-2016 All world wide rights reserved.