Subject: Glass Goose Sea Hawker cooling systems.
From: paul lamar
Date: 8/12/2016, 11:46 AM
To: A10-Me-Earthlink


  The RX8 core is a good core to use as are Chrysler Doge pick up
  cores. Large frontal area with thin cores. The Dodge core is 20" by
  30" and is very very effective in a cross counter flow configuration
  on the TTC engine. Two cores back to back.

  Let's take the Dodge in a non cross flow config.

  20 by 30 is 900 square inches.

  We have learned more about this subject since Neil Ungar started
  flying and on the time to climb engine. Neil complained about over
  cooling. It appears we can reduce the intake area of the wedge
  diffuser to 15%, of the frontal area of the core, from the  20%
  recommended previously.

  In other words 15% of 600 square inches is  90 square inches. The
  core is 20 inches wide so the height of the 4.5 inches high and 20
  inches wide.

  Both Neil and the TTC  rads are directly in the prop blast so if
  that is not the case then you may note higher water temp when
  taxiing.

  Here is the dodge core on top with the diffuser underneath. Yet
  another 3D :-) It is far enough forward to give room for the intake
  manifold behind it. This leaves room underneath for and oil cooler.

  The exhaust out the back of the cabin may help to attach more air to
  the aft sides of the cabin. This is a problem that was addressed by
  vortex generators previously (or in addition).

  Paul Lamar


  Excellent recommendations, thank you!   I was thinking of having the
  radiators on the top/back (low pressure) of the upper cowling with a
  long K&L duct.  Your version may be easier.   I will play with some
  radiator models on the actual engine.  The smaller the rad size the
  easier it will be to fit.  20x30 will be a challenge.

  In this model,  it seems that two 20x30x1 counterflow radiators
  would give a total volume of 1200ci?   Is it correct that we need
  about 600ci for water cooling and 200ci for oil?   If so, I assume
  that using cross counterflow rads would each need to be about 1/2 the
  Dodge size as long as I have 600ci?

  My RX8 has twin oil coolers about 8x10x2.  The single RX7 oil cooler
  is about the same volume.  The latter should fit up front if the
  water cooler intake is a little higher.

  Has anyone used 3D printing to create their engine cowling?

  Scott Gettings

  Those volume numbers depend on the thickness of the core. Thinner
  core less cubic inches are required as thin cores are far more
  efficient for a given volume. Dodge were leading the way with other
  manufactures catching on.

  This is a cross counter flow rad for a Tango

  14" by 24" They are Dodge Neon cores.

  Some what more compact at higher cost to make. You also need a
  skilled tig welder.

-------------------------------------------------------------------------


Scott,

  We should change the standard to square inches of frontal area
  because all the recent cores are around 5/8 to 3/4 inch thick
  including the RX8. Rad core frontal area is more correlated to
  cooling than volume.

  600 square inches frontal area for 250 HP single core. 2 x 300 square
  inches  for cross counter flow. Two Neon rads are about that. Maybe a
  bit more so they should handle a mild turbo charge.

  BTW have you considered a 8" prop extension to help the air stick to
  the cabin sides? You can lesson the angel at which they go back. If
  you go back at 7 degrees and then cut it off flat that will implement
  the Kamm effect. Same as the recent Preuses.


  Paul Lamar



  Hi Paul, I noticed during my re-search on the Glass Goose that the Icon A5
  also has issues back in the cabin sides. They have also used vortex
  generators in that area, on the test planes. The GG has the lower
  wing and the landing gear that also adds to the problems.

  Steve Steve Carlisle

Yes. It is a result of the side by side seating. That Icon is almost a scam.
Be wary?

With the Glass Goose it would not be that hard to change it to fore and aft seating
and narrow the cabin. That lower wing is necessary to keep the prop out
of the water spray which will destroy it.

Here are a couple of great books on seaplanes. Extensive discussion
of the unique design issues.

Paul Lamar

Correction fore and aft seating.

The Kamm 7 degrees does not work out well both side by side and
fore and aft.

The first 3D is side by side the rest are fore and aft.

Of course to build it fore and aft  seating one would have to start over.
Not practical for those already built.

Paul Lamar

IMHO if I were designing a sea plane I would scale something that
worked well like some of the Dornier's like the DO 26. Google it.

Actually the Schneider cup racers found out a long time ago
floats were lower drag than sea planes.

I also think a coot is a better than a glass goose.

Paul Lamar


 The Rotary Engine free News Letter. Powered by Linux. If you want
  off the list PLEASE let me know and I will remove  you.  ACRE NL web
  site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
  Copyright 1998-2016 All world wide rights reserved.