Subject: Glass Goose Sea Hawker cooling systems.
From: paul lamar
Date: 8/12/2016, 4:06 PM
To: A10-Me-Earthlink



    The RX8 core is a good core to use as are Chrysler Doge pick up
    cores. Large frontal area with thin cores. The Dodge core is 20" by
    30" and is very very effective in a cross counter flow configuration
    on the TTC engine. Two cores back to back.

    Let's take the Dodge in a non cross flow config.

    20 by 30 is 900 square inches.

    We have learned more about this subject since Neil Ungar started
    flying and on the time to climb engine. Neil complained about over
    cooling. It appears we can reduce the intake area of the wedge
    diffuser to 15%, of the frontal area of the core, from the  20%
    recommended previously.

    In other words 15% of 600 square inches is  90 square inches. The
    core is 20 inches wide so the height of the 4.5 inches high and 20
    inches wide.

    Both Neil and the TTC  rads are directly in the prop blast so if
    that is not the case then you may note higher water temp when
    taxiing.

    Here is the dodge core on top with the diffuser underneath. Yet
    another 3D :-) It is far enough forward to give room for the intake
    manifold behind it. This leaves room underneath for and oil cooler.

    The exhaust out the back of the cabin may help to attach more air to
    the aft sides of the cabin. This is a problem that was addressed by
    vortex generators previously (or in addition).

    Paul Lamar


    Excellent recommendations, thank you!   I was thinking of having the
    radiators on the top/back (low pressure) of the upper cowling with a
    long K&L duct.  Your version may be easier.   I will play with some
    radiator models on the actual engine.  The smaller the rad size the
    easier it will be to fit.  20x30 will be a challenge.

    In this model,  it seems that two 20x30x1 counterflow radiators
    would give a total volume of 1200ci?   Is it correct that we need
    about 600ci for water cooling and 200ci for oil?   If so, I assume
    that using cross counterflow rads would each need to be about 1/2 the
    Dodge size as long as I have 600ci?

    My RX8 has twin oil coolers about 8x10x2.  The single RX7 oil cooler
    is about the same volume.  The latter should fit up front if the
    water cooler intake is a little higher.

    Has anyone used 3D printing to create their engine cowling?

    Scott Gettings

    Those volume numbers depend on the thickness of the core. Thinner
    core less cubic inches are required as thin cores are far more
    efficient for a given volume. Dodge were leading the way with other
    manufactures catching on.

    This is a cross counter flow rad for a Tango

    14" by 24" They are Dodge Neon cores.

    Some what more compact at higher cost to make. You also need a
    skilled tig welder.

-------------------------------------------------------------------------


   Scott,

    We should change the standard to square inches of frontal area
    because all the recent cores are around 5/8 to 3/4 inch thick
    including the RX8. Rad core frontal area is more correlated to
    cooling than volume.

    600 square inches frontal area for 250 HP single core. 2 x 300 square
    inches  for cross counter flow. Two Neon rads are about that. Maybe a
    bit more so they should handle a mild turbo charge.

    BTW have you considered a 8" prop extension to help the air stick to
    the cabin sides? You can lesson the angel at which they go back. If
    you go back at 7 degrees and then cut it off flat that will implement
    the Kamm effect. Same as the recent Preuses.


    Paul Lamar



    Hi Paul, I noticed during my re-search on the Glass Goose that the Icon A5
    also has issues back in the cabin sides. They have also used vortex
    generators in that area, on the test planes. The GG has the lower
    wing and the landing gear that also adds to the problems.

    Steve Steve Carlisle

   Yes. It is a result of the side by side seating. That Icon is almost a scam.
   Be wary?

   With the Glass Goose it would not be that hard to change it to side by side
   and narrow the cabin. That lower wing is necessary to keep the prop out
   of the water spray which will destroy it.

   Here are a couple of great books on seaplanes. Extensive discussion
   of the unique design issues.


   Paul Lamar


Hi Paul, thanks for the insight. We have the "Flying Boats of World War II" in the museum.
Stranraer's used to fly out of the hanger, here in Coal Harbour, Vancouver Island.

Steve C

    The Rotary Engine free News Letter. Powered by Linux. If you want
    off the list PLEASE let me know and I will remove  you.  ACRE NL web
    site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
    Copyright 1998-2016 All world wide rights reserved.