Subject: Glass Goose Sea Hawker cooling systems.
From: paul lamar
Date: 8/12/2016, 7:50 PM
To: A10-Me-Earthlink



      The RX8 core is a good core to use as are Chrysler Doge pick up
      cores. Large frontal area with thin cores. The Dodge core is 20" by
      30" and is very very effective in a cross counter flow configuration
      on the TTC engine. Two cores back to back.

      Let's take the Dodge in a non cross flow config.

      20 by 30 is 900 square inches.

      We have learned more about this subject since Neil Ungar started
      flying and on the time to climb engine. Neil complained about over
      cooling. It appears we can reduce the intake area of the wedge
      diffuser to 15%, of the frontal area of the core, from the 20%
      recommended previously.

      In other words 15% of 600 square inches is  90 square inches. The
      core is 20 inches wide so the height of the 4.5 inches high and 20
      inches wide.

      Both Neil and the TTC  rads are directly in the prop blast so if
      that is not the case then you may note higher water temp when
      taxiing.

      Here is the dodge core on top with the diffuser underneath. Yet
      another 3D :-) It is far enough forward to give room for the intake
      manifold behind it. This leaves room underneath for and oil cooler.

      The exhaust out the back of the cabin may help to attach more air to
      the aft sides of the cabin. This is a problem that was addressed by
      vortex generators previously (or in addition).

      Paul Lamar


      Excellent recommendations, thank you!   I was thinking of having the
      radiators on the top/back (low pressure) of the upper cowling with a
      long K&L duct.  Your version may be easier.   I will play with some
      radiator models on the actual engine.  The smaller the rad size the
      easier it will be to fit.  20x30 will be a challenge.

      In this model,  it seems that two 20x30x1 counterflow radiators
      would give a total volume of 1200ci?   Is it correct that we need
      about 600ci for water cooling and 200ci for oil?   If so, I assume
      that using cross counterflow rads would each need to be about 1/2 the
      Dodge size as long as I have 600ci?

      My RX8 has twin oil coolers about 8x10x2.  The single RX7 oil cooler
      is about the same volume.  The latter should fit up front if the
      water cooler intake is a little higher.

      Has anyone used 3D printing to create their engine cowling?

      Scott Gettings

      Those volume numbers depend on the thickness of the core. Thinner
      core less cubic inches are required as thin cores are far more
      efficient for a given volume. Dodge were leading the way with other
      manufactures catching on.

      This is a cross counter flow rad for a Tango

      14" by 24" They are Dodge Neon cores.

      Some what more compact at higher cost to make. You also need a
      skilled tig welder.

-------------------------------------------------------------------------


    Scott,

      We should change the standard to square inches of frontal area
      because all the recent cores are around 5/8 to 3/4 inch thick
      including the RX8. Rad core frontal area is more correlated to
      cooling than volume.

      600 square inches frontal area for 250 HP single core. 2 x 300 square
      inches  for cross counter flow. Two Neon rads are about that. Maybe a
      bit more so they should handle a mild turbo charge.

      BTW have you considered a 8" prop extension to help the air stick to
      the cabin sides? You can lesson the angel at which they go back. If
      you go back at 7 degrees and then cut it off flat that will implement
      the Kamm effect. Same as the recent Preuses.


      Paul Lamar



      Hi Paul, I noticed during my re-search on the Glass Goose that the Icon A5
      also has issues back in the cabin sides. They have also used vortex
      generators in that area, on the test planes. The GG has the lower
      wing and the landing gear that also adds to the problems.

      Steve Steve Carlisle

    Yes. It is a result of the side by side seating. That Icon is almost a scam.
    Be wary?

    With the Glass Goose it would not be that hard to change it to fore and aft seating
    and narrow the cabin. That lower wing is necessary to keep the prop out
    of the water spray which will destroy it.

    Here are a couple of great books on seaplanes. Extensive discussion
    of the unique design issues.

    Paul Lamar

    Correction fore and aft seating.

    The Kamm 7 degrees does not work out well both side by side and
    fore and aft.

    The first 3D is side by side the rest are fore and aft.

    Of course to build it fore and aft  seating one would have to start over.
    Not practical for those already built.

    Paul Lamar

    IMHO if I were designing a sea plane I would scale something that
    worked well like some of the Dornier's like the DO 26. Google it.

    Actually the Schneider cup racers found out a long time ago
    floats were lower drag than sea planes.

    I also think a coot is a better than a glass goose.


    Paul Lamar

Hi Paul, I stumbled across this amphibian concept, made in PlaneMaker, for Xplane.  It likely has no turbulence issues, a lot like the SeaRay amphibian. Applying this parasol wing and aft cabin mods together with interplane struts would also lift the prop out of the water, no need to put a prop dam on the empenage.

Inline image 1

Steve Carlisle

Looks like it violates the 7 degree rule.

Paul Lamar

     The Rotary Engine free News Letter. Powered by Linux. If you want
      off the list PLEASE let me know and I will remove  you.  ACRE NL web
      site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
      Copyright 1998-2016 All world wide rights reserved.