Subject: Pre-chamber initiated jet ignition
From: paul lamar
Date: 8/30/2016, 7:52 AM
To: A10-Me-Earthlink



Paul,

During my combustion testing on rotary engines I kept finding an
anomaly of autoignition.  Usually about 6 to 8 cycles on a normal
8000 RPM sweep. It seemed to be caused by exhaust reversion
continuing to the next intake cycle and causing the auto ignition.
Very scary to have an uncontrolled ignition source.... but the good
news was that the burn rate on those cycles improved!

After a little study I discovered a Honda experiment that concluded
with a race bike for the Dakar rally that had a two-stroke engine
running without ignition and getting 20% better fuel economy. But the
details were very sketchy.

Fast forward to Formula 1 today. They are using what is known as
Turbulent Jet Ignition. This process is not new, it was discovered
by Ricardo and published in his papers from 1911. The latest version
of this process by Mahle uses a direct injector and spark plug in a
very small pocket that injects active radicals into the main
combustion chamber. The engine can then be operated almost like a
diesel and the burning process is spread throughout the combustion
chamber by quenched active radicals causing a very fast burn rate.
Lean burns have been demonstrated to lambda 2 or 30:1 AFR gasoline
and throttling losses greatly reduced.

This is why Formula One is now  producing the same horsepower but is
using 40% less fuel. Mahle  is reportedly working with Ferrari but
Mercedes seems to be way ahead of them.

This ignition process seems to be a perfect fit for the rotary
engine... especially on aircraft where BSFC is so important.

Barry Bordes



How are you doing the combustion testing on rotary engines?
References for the Honda experiment?

http://papers.sae.org/2010-01-1457/

The reason Formula One engines are burning less fuel is because they
are turbo compound hybrids. A formula 1 engine is either on full
throttle or on the brakes. The power recovery from braking is  a
large part of that.

http://www.rotaryeng.net/Oxford-TC-talk.mp4

We have known for years that leaning the rotary up to 18:1 improves
the BSFC at the expense of power.

If you have a leaking apex seal hot exhaust gases from the leading
chamber can pre ignite the following chamber.

Paul Lamar


I am using an Optrand sensor in the leading spark plug.  In
conjunction with a TFX logger.

See attachments for the type data it provides. The first is a peak
pressure single cycle with exhaust opening pressure and temp. The
second shows burn rate The third shows a complete 7000 rpm run....
tuning a new EFR turbo... the lower cells around 4000 rpm are
retarded.

I don't have the Honda paper number but check SAE 2010-01-2263 for
past and  present research. Barry Bordes

Looks like it is sparking  After Top Dead Center.

We use 22 degrees BTC


Paul Lamar

That timing was initiated at approximately 22 deg BTDC.  It takes
the kernel that long to grow into a readable pressure at 9 deg ATDC.
The rate then snowballs from the heat and pressure.

I adjust the timing to place the peak pressure at about 45 deg ATDC.
(less at lower RPM) What we are seeing is how slow the burn is with
standard ignition practices.

Barry Bordes

That is amazing. What does that device cost?


Paul Lamar


They have many systems from one to 28 high speed loggers. Sensors are
extra. Here is a link with lots of info. Great knowledgeable
support. My contact is Clint Grey.

TFX Engine Technology - Engine Pressure Analyzers
<http://www.tfxengine.com/hardware3.html



image <http://www.tfxengine.com/hardware3.html


Thanks.

I don't need a logger. A Maximite is a great logger. Super low cost.

This is some interesting research by Honda. Maybe they can use this
to help their lagging F1 turbo compound hybrid engine development.

"When the fuel is brought to the right pressure and temperature, the
molecules break down into what are known as active radical molecules.
These are highly unstable chemical compounds which are an
intermediate step in the actual combustion reaction. When hot exhaust
gas remains in the [chamber], it contains a small percentage of
active radical molecules; when these are combined with the incoming
fuel charge, the resulting mixture begins to auto-ignite at lower
temperature that a pure gasoline/air mixture. What we currently
associate with auto-ignition is engine knock, a phenomenon that
occurs when the fuel ignites before the spark plug fires."

Dan Gorsline  clued me in on this.


Paul Lamar



Honda's approach was to use an overextending exhaust power valve that could trap the active radicals from the preceding ignition sequence to be used by the next intake charge for ignition.
The rotary may be made to use the same process by having a valve that would induce reversion into the intake charge.
Internal EGR.

Barry Bordes


There is already reversion depending on which style of ports are selected.

In order
P-port exhaust and intake...a lot
P-port intake side exhaust
P-port exhaust side intake
Side exhaust side intake RX8. very little.

There is aways some from the bath tube in the rotor face.

With  turbo charged engine if a little high pressure intake  air is diverted
to tiny holes in the rotor housing between intake and exhaust ...Less.

Paul Lamar

The Rotary Engine free News Letter. Powered by Linux. If you want
off the list PLEASE let me know and I will remove  you.  ACRE NL web
site. http://www.rotaryeng.net/YouTubehttp://tinyurl.com/beqqxas
Copyright 1998-2016 All world wide rights reserved.