Subject: What Oz needs is a fast long range bush plane
From: paul lamar
Date: 9/4/2016, 12:16 PM
To: A10-Me-Earthlink


 A 500 HP turbo two  rotor could be made and sold for less than
 $20,000 using stock Mazda e-shaft, rotor housings and rotors.
 Aluminum end and center housings.

 The 500 HP  two rotor rotary  is needed to get off fast on short,
 rough runways.

 This will hold four people or two people and two stretchers.

 The key to a bush plane is great big balloon tires. Unfortunately
 they are a lot of drag which effects the speed and range.

 The catamaran configuration is ideal to retract two large balloon
 tires with out adding a lot of drag and complication.

 The two long hydraulic cylinders on each wheel feed into an
 accumulator when in the landing mode. When retracting the accumulator
 is turned off and the oil sucked out of the top of the  cylinders to
 retract the gear.

 Almost all loads from the gear feed directly into the spar. The
 strongest place in any airplane.  The engine is mounted above and to
 the spar. It can be a tractor or pusher.

 Keep it  simple.

 I'll bet some one can get a grant from the Oz gov as it is much lower
 cost than the turbo props they are using now. This is low cost
 enough so ranchers, farmers  and so fourth can afford it. No need for
 waiting for a flying doctor turbo prop to get there if someone is
 injured or gets sick.

 You can show this at Oz-Kosh Dave.

 Paul Lamar


 Very nice. So could you have balloon tires and hydro foils in one
 configuration?

 Thanks, Paul.

 Sincerely,

 Boyd Thompson

 I thought about that but it is difficult as the gear and the hydro
 foils, I think, want to be in the same position relative to the CG.
 The other problem is the empty weight would be higher.

 What can be done is seal the wheel wells, beef up the gear doors and
 land in water if absolutely necessary. For example running out of
 gas.

 I am working on a simpler and cheaper mold for making the composite
 fuselage. Part of it can be flat and consequently  plywood can be
 used for some of the male mold.

 What works for mold separation is ordinary duct tape. You cover the
 entire male buck with it. Plywood and all so it matters not what you
 make the male buck out of. One could use blue Styrofoam (expensive)
 for the compound surfaces  or ordinary wall plaster. Much cheaper.
 Also thin galvanized sheet steel as found in air coordinating ducts
 could be used for simple curved surfaces.

 We used special auto body styling clay at Chaparral.

 The key is slather on micro balloons mixture on the cured layup and
 sand most of it off. That tells you were the depressions are. Works
 for foam core fiberglass wings as well.

 Here is a hood for an Austin Healy Sprite I made 55 years ago. The
 silver bumpers are  part of the hood made from fiberglass. Beefed up
 of course.

 If I knew then what I know now learned from Dan Gray about making
 fiberglass molds it would have been much smoother :-)

 I don't think we had duct tape in those days either :-)

 Paul Lamar


 Paul,

 The perfect, reasonably fast bush plane already exists.  It is the
 Helio Courier, and if you want more, there is the Helio Stallion.
 Replace the GO-480 Lycoming in the Courier and the PT-6 in the
 Stallion.  http://helioaircraft.com/default.htm

 Steve Brazil

Good bush planes for fairly hard, relatively smooth  surfaces. Not so for soft sand
or rocks.

The best bush planes have balloon tires or floats.

Around Ventura we have a lot of plowed fields.

One could probably land in the direction of the furrows or even in
the river bed with balloon tires.

Paul Lamar

 The Rotary Engine free News Letter. Powered by Linux. If you want
 off the list PLEASE let me know and I will remove  you.  ACRE NL web
 site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
 Copyright 1998-2016 All world wide rights reserved.