Subject: The correct flywheel for RX8 opss forgot the pics
From: paul lamar
Date: 9/5/2016, 8:32 AM
To: A10-Me-Earthlink



 ------------------------- *From:* paul lamar
 <rotaryeng@earthlink.net *To:* A10-Me-Earthlink
 <rotaryeng@earthlink.net *Sent:* Sunday, 4 September 2016, 22:39
 *Subject:* The correct flywheel for RX8 opss forgot the pics



 Hello Paul, Can you tell me which flywheel is the correct one to fit
 to a RX8 engine. I have removed the manual flywheel. Do I need a
 balance section from the automatic engine as well as the flywheel.
 Your help is appreciated . Regards

 Mark Dillar

 You need an RX8 automatic transmission flex plate and counter
 weight. Don't use Tracy's flex coupling. It over stresses the flex
 plate and may cause it to crack. Of course you can buy an after
 market expensive chrome molly steel flex plate/flywheel. That is
 what Dave Leonard did.

 Or use one of our couplings like the one used on the TTC engine.

 I have some water jet cut parts left  for the steel version. Weld it
 your self.

 Paul Lamar

 Thank you Paul, It's early days for me working on the Mazda so I
 shall start the search for the flex plate and counter weight. I shall
 hold on the coupling but will go back through the emails to see the
 pictures of the ttc coupler Thank you for the information that I do
 get from your News Letter and I hope you don't mind if I should
 forward further questions to you

 Mark Dillar

 I sent pictures of the TTC coupling. Did you see the aluminum
 version? That was the TTC coupling. If you are using a cell phone
 they sometimes are limited to the number of pictures they will
 download.

 The TTC coupling could be half the length for an ordinary two rotor.
 The diameter would be the same as it picks up the six high strength
 bolts in the counter weight.

 The stock E-shaft and counter weight are way over designed for a 250
 HP normally aspirated p-port 2 rotor. I suspect 1500 HP would be no
 problem. The three and four rotor turbo's are using the same parts.

 Here are some more pictures of the TTC coupling. The flex plate shown
 is an after market aluminum version.

 Paul Lamar



 Got them thanks Paul. Both the plate and the coupling are really
 nice. Looking back , a coupling like your steel coupling would be
 ideal for my requirements Is the rubber available easily?

 Mark Dillar


 It is in the states from McMaster Carr.

 I can mail you a block to the UK if necessary. It is easily cut with
 a band saw or hack saw. It can also be drilled to soften it.

 Here is a scr capture from McMaster.



 Paul Lamar


 How much would I be looking at, in round figures, for you to send me
 the water jet cut parts and the silicone Paul?

Mark Dillar

I am not sure about the postage.
The parts and the silicon would be $50 US cash in the mail.
I have enough silicon left over from the TTC project so no Macmaster Carr $50.
I'll get back to you on the postage cost.

I redesigned it in metric so you can get the rest of the parts in the UK.
The Formula 1 constructors must have a bunch of metal suppliers that they use.

Do you know my rotary engine  friend Eamon Hurley in Coventry. Is he he still alive?

He stepped off his rotary powered bike at 175 MPH and lived to tell about it years ago  :-)
He can help you a lot.

What are you going to use for a gear box?

Do you have 3D drawing software?

Paul Lamar


 The Rotary Engine free News Letter. Powered by Linux. If you want
 off the list PLEASE let me know and I will remove  you.  ACRE NL web
 site. http://www.rotaryeng.net/YouTubehttp://tinyurl.com/beqqxas
 Copyright 1998-2016 All world wide rights reserved.