Subject: Lots of power Radial rotary
From: paul lamar
Date: 9/19/2016, 8:01 AM
To: A10-Me-Earthlink


     Just a thought to chew on.  I think most folks love the old radial
     engines.  If you look at the max diameter of the wright engines, it
     is about 54 inches.


     Lets stretch our imagination and put 3 to 9 rotaries  within circle
     with the outside being 54 inches.  They could be mounted with the
     base outward easily within the 54 inch circle.


     Each engine can have a gear on the output shaft driving a center gear
     on the prop shaft, easily making the 3 to one gear down required for
     the prop.   Nine rotary engines with 2 rotors each times 650 hp each
     is 5850 .hp and the same frontal area as an old radial engine. Maybe
     less weight too.

     Maybe an overrun clutch on the drive gears to shut a few down for
     cruise.

     Really good redundancy as well.  Might draw one up on the cad
     system.

     Ken Burdgess

     Interesting idea.

     Don't stop at 3 to one. Make it 4 or 5 or more  to one and use a
     really big prop or helicopter rotor. One way to get gobs of torque
     out of several rotaries.

     That would make a really great helicopter engine.

     Paul Lamar


   You would need a killer radiator to handle the cooling needs of 6000 HP
   worth of fire breathing rotary power.  Add an energy recovery turbine in
   the mix for each pair of rotary engines and you would have an unbeatable
   BSFC to go along with all the other benefits of rotary power.

   Mark LaPierre


   Here is what a 4 rotary radial  helicopter engine might look like.
   The engines are one rotor engines because lubrication is an issue
   with vertically mounted 2 rotor rotaries. Sachs made a lawn mower
   with a vertically mounted one rotor.

   Turbo charged you would have about  1000 to 1300  HP to work with.
   The lack of a traditional helicopter planetary  gear box is a big advantage.

   My guess on weight is about 500 to 650 pounds.
   Unprecedented power to weight ratio. Better than a PT6.

---------------------------------------------------------------------------------

   Here is a better 3D of the helicopter engine using aluminium end housings
   and no oil pans. I suspect the dry sump and oil pressure pumps could be
   incorporated into the end housing. It is on a some what tighter 36 inch
   diameter circle over all.

   A corncob version with four 4 rotors would have less frontal area
   than  the CW R3350 used in the B29 and the P&W R4360  used in the
   B36 and the Spruce Goose. HP would be 5,200 or so. The P&W was
   only 4200 HP.

   Make a good boat engine and be easier to cool as well.

   Thanks for thinking of this Ken. IMHO we have just seen the very
   beginning of the Wankel engine.

   Paul Lamar

Paul and Ken,

What about placing the four gears under the "output shaft driving a center gear
 on the prop shaft" (running the prop shaft from inside the circumference) reducing the diameter of the engine frontage by the diameter of the rotary output shaft gears.  I think you can vary the ratio by gear diameter also? Perhaps dropping the overall 54 inches to under 44 inches.

George F. Curtis Jr.

I don't follow you George. Us MS Paint and make a sketch.

The diameter is now only 36 inches and not 54.

Paul Lamar


   The Rotary Engine free News Letter. Powered by Linux. If you want off
   the list PLEASE let me know and I will remove  you.  ACRE NL web
   site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
   Copyright 1998-2016 All world wide rights reserved.