Just a thought to chew on. I think most folks love the old radial
engines. If you look at the max diameter of the wright engines, it
is about 54 inches.
Lets stretch our imagination and put 3 to 9 rotaries within circle
with the outside being 54 inches. They could be mounted with the
base outward easily within the 54 inch circle.
Each engine can have a gear on the output shaft driving a center
gear on the prop shaft, easily making the 3 to one gear down required
for the prop. Nine rotary engines with 2 rotors each times 650 hp
each is 5850 .hp and the same frontal area as an old radial engine.
Maybe less weight too.
Maybe an overrun clutch on the drive gears to shut a few down for
cruise.
Really good redundancy as well. Might draw one up on the cad
system.
Ken Burdgess
Interesting idea.
Don't stop at 3 to one. Make it 4 or 5 or more to one and use a
really big prop or helicopter rotor. One way to get gobs of torque
out of several rotaries.
That would make a really great helicopter engine.
Paul Lamar
You would need a killer radiator to handle the cooling needs of 6000
HP worth of fire breathing rotary power. Add an energy recovery
turbine in the mix for each pair of rotary engines and you would have
an unbeatable BSFC to go along with all the other benefits of rotary
power.
Mark LaPierre
Here is what a 4 rotary radial helicopter engine might look like.
The engines are one rotor engines because lubrication is an issue
with vertically mounted 2 rotor rotaries. Sachs made a lawn mower
with a vertically mounted one rotor.
Turbo charged you would have about 1000 to 1300 HP to work with.
The lack of a traditional helicopter planetary gear box is a big
advantage.
My guess on weight is about 500 to 650 pounds. Unprecedented power to
weight ratio. Better than a PT6.
---------------------------------------------------------------------------------
Here is a better 3D of the helicopter engine using aluminium end
housings
and no oil pans. I suspect the dry sump and oil pressure pumps could
be incorporated into the end housing. It is on a some what tighter 36
inch diameter circle over all.
A corncob version with four 4 rotors would have less frontal area
than the CW R3350 used in the B29 and the P&W R4360 used in the B36
and the Spruce Goose. HP would be 5,200 or so. The P&W was only 4200
HP.
Make a good boat engine and be easier to cool as well.
Thanks for thinking of this Ken. IMHO we have just seen the very
beginning of the Wankel engine.
Paul Lamar
Paul and Ken,
What about placing the four gears under the "output shaft driving a
center gear on the prop shaft" (running the prop shaft from inside
the circumference) reducing the diameter of the engine frontage by
the diameter of the rotary output shaft gears. I think you can vary
the ratio by gear diameter also? Perhaps dropping the overall 54
inches to under 44 inches.
George F. Curtis Jr.
I don't follow you George. Us MS Paint and make a sketch.
The diameter is now only 36 inches and not 54.
Paul Lamar
Not really a new idea...
https://youtu.be/Q2IFWveYBRs
Each plate section has 3 siamesed sections as does each housing
section.
Dan Gorsline.
The solution that R12 choose was to create 3 banks of four rotors using
top two banks to help the bottom bank as the output shaft.
R12 Gear Arrangement includes idler gear to allow the right two banks
to turn the same direction, while the top left bank is counter
rotating...
<http://www.enginelabs.com/news/video-exotic-12-rotor-rotary-engine-ready-for-dyno/>
R12 Specifications speaks well for the concept put forth, Radial Rotary
Engine opens new Realms to the Wankel Engine...
<http://www.12rotor.com/p/specifications.html>
George F. Curtis Jr.
The Rotary Engine free News Letter. Powered by Linux. If you want
off the list PLEASE let me know and I will remove you. ACRE NL web
site.
http://www.rotaryeng.net You Tube
http://tinyurl.com/beqqxas
Copyright 1998-2016 All world wide rights reserved.