Subject: OMC oil cooling the rotor. FIXED!!!
From: paul lamar
Date: 9/23/2016, 12:26 AM
To: A10-Me-Earthlink



I have a sachs and a OMC but they are charged cooled.
How can we cool them better than adding water cooling to the end
plates and
the housing?

David Mikesell


Not easy. Convert to an oil cooled  rotor.

I had not thought of this idea before but our good experience with the
dry sump
system on the TTC engine suggest the way to do it is have a totally
independent oil
system with the sole purpose of squirting cooling oil up into the
rotor.

You need to figure out a way to get pressurized oil into a hollow
E-shaft.
A scavenge pump should be able to recover this and feed it through
an oil cooler. No need to change any of the bearings.


--------------------------------------------------------------------------------

Block off all that mickey mouse charge cooling stuff and use the
butter fly
valve as the throttle for the p-port.

There will be enough oil sloshing around in there to lube the bearings.
You will need a two section dry sump pump. One for pressure and
the other for scavenging. Use Mobil 1.

Still mix oil with the fuel to lube the apex seals.

This could be BIG if it works. LOTS more HP!!!

Should work on just about all charged cooled engines.


Paul Lama

Sounds like a project I want to do!

I think I will try it on the Sachs first. I have more of them than the
nicer OMC.

I have another question though, what would be the best way to monitor
the temperature to keep from melting the rotor or over temping the seals
are causing heat damage?

-------------------------------------------------------------------
Looks good, but wouldn't just a really small oiling hole in the E shaft
work to spray cooling oil and bearing oil into the cavity?

Your idea of using the butterfly as a P port? Won't it cause a bit of
restriction with the 90degree bend right after the butterfly into the
housing?
Maybe hole saw thru the area to give a straight entry to keep the air
velocity higher?

I have see pictures of P port conversions, but what is the proper way
and design changes needed for the P port?

The port in each end housing would give a easy way to have the oil drain
out to a scavenge pickup if the engine is in a vertical shaft application.
Which is actually one of the ongoing projects. A ultralight helicopter.
With the reduction ideas you have given me it seems to be right for that
project
too.

David Mikesell

I think one can get paint that changes color according to temperature.

Straight in for a P-port is great. The OMC needs modification to make it
straight in.

I think you need the oil squirter tube. Perhaps even two of them pointing
apart at a 10 or 20 degree angle. That rotor runs HOT!.

-----------------------------------------------------------------------------

Latest thinking on this is a oil squirter tube will not work on an OMC
e-shaft.

What will work is place the oil squirter in the end housing #1 in this
depression in the lower part. This depression lines up with the hollow
part of the rotor over and over again. There is a corresponding depression
in the opposite #2 end housing. That should be filled with epoxy or
a metal plug. That keeps the cooling oil in the rotor until the
rotor is aligned  with the first depression again.  Each rotor cavity
is cooled in turn.

The scavenge system is plumbed to the same depression. The hot oil is
then fed
through an oil cooler and back to the oil squirter.

There is enough oil sloshing around to lube all the roller bearings.

That's it. That is all it takes. Will work on all charged cooled engines.
No major modifications to anything.


Better VE as you are not heating the air/fuel  charge.
More power for the same reason. WOT indefinitely.

--------------------------------------------------------------------------------
Here is what a large dry sump pump looks like. It is for 520 CI
aerobatic aircraft engine.

We will need a smaller version to cool the charged cooled engines
and for use on the Mazda.

Building a smaller dry sump pump is the next project.


Paul Lamar


Great information. I am still about a week out before I have the time to
start modifying my Sachs. If it works then I will trying it on the OMC next.

David Mikesell

There are some electric, high pressure oil pumps on the market.
They are used for pre oiling boat engines. This is a cheap way
to test it.

--------------------------------------

This is what the engine driven pump will look like more or less.
It will be a couple of months before I can get these made.
Price will be around $150.

Size is 3 x 2 x 5 inches.

Paul Lamar

 The Rotary Engine free News Letter. Powered by Linux. If you want off
the list PLEASE let me know and I will remove  you.  ACRE NL web
site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
Copyright 1998-2016 All world wide rights reserved.