Subject: OMC oil cooling the rotor. FIXED!!!
From: paul lamar
Date: 9/24/2016, 6:59 PM
To: A10-Me-Earthlink


 I have a sachs and a OMC but they are charged cooled. How can we cool
 them better than adding water cooling to the end plates and the
 housing?

 David Mikesell


 Not easy. Convert to an oil cooled  rotor.

 I had not thought of this idea before but our good experience with
 the dry sump system on the TTC engine suggest the way to do it is
 have a totally independent oil system with the sole purpose of
 squirting cooling oil up into the rotor.

 You need to figure out a way to get pressurized oil into a hollow
 E-shaft. A scavenge pump should be able to recover this and feed it
 through an oil cooler. No need to change any of the bearings.


 --------------------------------------------------------------------------------



Block off all that mickey mouse charge cooling stuff and use the butter fly valve as the throttle for the p-port.

 There will be enough oil sloshing around in there to lube the
 bearings. You will need a two section dry sump pump. One for pressure
 and the other for scavenging. Use Mobil 1.

 Still mix oil with the fuel to lube the apex seals.

 This could be BIG if it works. LOTS more HP!!!

 Should work on just about all charged cooled engines.


 Paul Lama

 Sounds like a project I want to do!

 I think I will try it on the Sachs first. I have more of them than
 the nicer OMC.

 I have another question though, what would be the best way to monitor
 the temperature to keep from melting the rotor or over temping the
 seals are causing heat damage?

 -------------------------------------------------------------------
 Looks good, but wouldn't just a really small oiling hole in the E
 shaft work to spray cooling oil and bearing oil into the cavity?

 Your idea of using the butterfly as a P port? Won't it cause a bit of
 restriction with the 90degree bend right after the butterfly into the
 housing? Maybe hole saw thru the area to give a straight entry to
 keep the air velocity higher?

 I have see pictures of P port conversions, but what is the proper way
 and design changes needed for the P port?

 The port in each end housing would give a easy way to have the oil
 drain out to a scavenge pickup if the engine is in a vertical shaft
 application. Which is actually one of the ongoing projects. A
 ultralight helicopter. With the reduction ideas you have given me it
 seems to be right for that project too.

 David Mikesell

 I think one can get paint that changes color according to
 temperature.

 Straight in for a P-port is great. The OMC needs modification to make
 it straight in.

 I think you need the oil squirter tube. Perhaps even two of them
 pointing apart at a 10 or 20 degree angle. That rotor runs HOT!.

 -----------------------------------------------------------------------------



Latest thinking on this is a oil squirter tube will not work on an OMC e-shaft.

 What will work is place the oil squirter in the end housing #1 in
 this depression in the lower part. This depression lines up with the
 hollow part of the rotor over and over again. There is a
 corresponding depression in the opposite #2 end housing. That should
 be filled with epoxy or a metal plug. That keeps the cooling oil in
 the rotor until the rotor is aligned  with the first depression
 again.  Each rotor cavity is cooled in turn.

 The scavenge system is plumbed to the same depression. The hot oil is
 then fed through an oil cooler and back to the oil squirter.

 There is enough oil sloshing around to lube all the roller bearings.

 That's it. That is all it takes. Will work on all charged cooled
 engines. No major modifications to anything.


 Better VE as you are not heating the air/fuel  charge. More power for
 the same reason. WOT indefinitely.

 --------------------------------------------------------------------------------


Here is what a large dry sump pump looks like. It is for 520 CI aerobatic aircraft engine.

 We will need a smaller version to cool the charged cooled engines and
 for use on the Mazda.

 Building a smaller dry sump pump is the next project.


 Paul Lamar


 Great information. I am still about a week out before I have the time
 to start modifying my Sachs. If it works then I will trying it on the
 OMC next.

 David Mikesell

 There are some electric, high pressure oil pumps on the market. They
 are used for pre oiling boat engines. This is a cheap way to test
 it.

 Paul Lamar


 Hi Paul, Where do I buy one of those Bulent pre oiler pumps. Cheers
 Chris.Hoskins

Sorry about the delay on this Chris.

It is a yacht engine thing. Here is a picture of the installed unit.

Bulent is not the Brand name. He is just the guy that came up with the
idea.

Paul Lamar


 The Rotary Engine free News Letter. Powered by Linux. If you want off
 the list PLEASE let me know and I will remove  you.  ACRE NL web
 site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
 Copyright 1998-2016 All world wide rights reserved.