Subject: KITPLANES The Independent Voice for Homebuilt Aviation - Engine Theory - KITPLANES Article
From: paul lamar
Date: 9/26/2016, 1:18 PM
To: A10-Me-Earthlink
CC: Paul Dye <editorial@kitplanes.com>



The conclusion is that automobile conversions are doomed to fail
because no one (other than deep pocketed Rotax) can design and test a
PSRU that survives vibratory forces.

http://www.kitplanes.com/issues/33_10/builder_spotlight/Engine-Theory-geared-drive_21647-1.html <http://www.kitplanes.com/issues/33_10/builder_spotlight/Engine-Theory-geared-drive_21647-1.html>

Barry Gloger

That is strange. All those people (hundreds) that have been flying
rotaries  for thousands of accumulated hours on the Ross and Tracy Crook
gear boxes based on the Ford Planetary
since 1973 must have dreamed they were flying. Dave Leonard has over 650
hours with a turbo rotary and Tracy's GB  I estimate has well over 200 HP.

The vast majority of radial engines since the 1920's or so have had gear
boxes and that includes the P&W R4360 corn cob engine.  Not rotary engines....
radial engines. Most are planetaries. A piston engine is much harder on gear boxes than
a rotary.  It is not that hard to design a gear box.

The current editor of Kit Planes is uneducated on aircraft  gear boxes among
many other things. I don't buy  Kit Planes  anymore. It is not worth it.
No real info in terms of numbers. Just a lot of bull shit.

Paul Lamar


The article does state that planetary PSRU’s used with WWII & DC-6’s Pratt & Whitney Radials were successful, but took years to develop & test

If the Ford planetary works, why are folks constantly writing you for suggestion & designs for Wankel engines?

The article points out it’s not just the PRSU, but that the engine, PSRU & Prop must be tested as a unit

Another article (self serving) in that same issue discuss vibration testing

Barry Gloger

Because Tracy Crook retired and stopped making gear boxes.
Several people are building their own and a couple are working on
introducing a new one all based on the original Ross design back in
1973.


I am looking at ways to simplify it and reduce the weight and cost.

Vibration? We don't have any stinking vibration :-)
You want vibration look at a four cylinder aircraft engine.

Paul Lamar


When they are discussing vibration problems, they have not removed their head from the recipient engine rectum. Rotary engines display minimal vibration as long as the proper balance weights are used for the e-shaft eccentric weight.


Reciprocating engines depending on the basic design can display a number of vibration tendencies.  There are noted vibrations listed as orders. Primary and secondary are the main issues to note. In line four cylinder 4 stroke engines have secondary harmonic shaking vibration. This is what makes them "buzzy" as the RPM gets higher like freeway speeds. This is caused by the engine center of gravity changing twice per engine revolution.

At TDC and BDC the center of gravity is at one place. At 90 degrees before and after TDC the Pistons are lower than 1/2 the stroke. This is because the conn rod goes down the 1/2 stroke plus to the side that much. Pythagoras theory and math.

Then two cylinder engines, whether both Pistons travel together or 180 degrees apart. Odd number cylinders develop a rocking force. V6 engines are terrible depending on which design.

Dale Davies

The real reason automotive piston engines are doomed to fail is they are light
duty engines. They almost never see full power.

The Mazda Wankel on the other hand is capable of 100% duty cycle up to three
times the stock installed power in the RX8.

Paul Lamar

The Rotary Engine free News Letter. Powered by Linux. If you want off
the list PLEASE let me know and I will remove  you.  ACRE NL web
site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
Copyright 1998-2016 All world wide rights reserved.