Subject: Lots of power Radial rotary
From: paul lamar
Date: 9/28/2016, 5:07 AM
To: A10-Me-Earthlink



   Just a thought to chew on.  I think most folks love the old radial
   engines.  If you look at the max diameter of the wright engines, it
   is about 54 inches.


   Lets stretch our imagination and put 3 to 9 rotaries  within circle
   with the outside being 54 inches.  They could be mounted with the
   base outward easily within the 54 inch circle.


   Each engine can have a gear on the output shaft driving a center gear
   on the prop shaft, easily making the 3 to one gear down required for
   the prop.   Nine rotary engines with 2 rotors each times 650 hp each
   is 5850 .hp and the same frontal area as an old radial engine. Maybe
   less weight too.

   Maybe an overrun clutch on the drive gears to shut a few down for
   cruise.

   Really good redundancy as well.  Might draw one up on the cad
   system.

   Ken Burdgess

   Interesting idea.

   Don't stop at 3 to one. Make it 4 or 5 or more  to one and use a
   really big prop or helicopter rotor. One way to get gobs of torque
   out of several rotaries.

   That would make a really great helicopter engine.

   Paul Lamar


   You would need a killer radiator to handle the cooling needs of 6000
   HP worth of fire breathing rotary power.  Add an energy recovery
   turbine in the mix for each pair of rotary engines and you would
   have an unbeatable BSFC to go along with all the other benefits of
   rotary power.

   Mark LaPierre


   Here is what a 4 rotary radial  helicopter engine might look like.
   The engines are one rotor engines because lubrication is an issue
   with vertically mounted 2 rotor rotaries. Sachs made a lawn mower
   with a vertically mounted one rotor.

   Turbo charged you would have about  1000 to 1300  HP to work with.
   The lack of a traditional helicopter planetary  gear box is a big
   advantage.

   My guess on weight is about 500 to 650 pounds. Unprecedented power
   to weight ratio. Better than a PT6.

---------------------------------------------------------------------------------



   Here is a better 3D of the helicopter engine using aluminum end
   housings and no oil pans. I suspect the dry sump and oil pressure
   pumps could be incorporated into the end housing. It is on a some
   what tighter 36 inch diameter circle over all.

   A corncob version with four 4 rotors would have less frontal area
   than  the CW R3350 used in the B29 and the P&W R4360  used in the
   B36 and the Spruce Goose. HP would be 5,200 or so. The P&W was only
   4200 HP.

   Make a good boat engine and be easier to cool as well.

   Thanks for thinking of this Ken. IMHO we have just seen the very
   beginning of the Wankel engine.

   Paul Lamar


   I fantasized about this config back when I was in love with the
   Griffon Lionheart.

   Chris Cosman


   Well this is s great idea, mechanically, but who in their right mind
   would be the one to start it up, instant hearing loss !

   steve Carlisle

   Imagine a DH Beaver with one of these? About the same weight and size
   as the Beaver engine. The noise would be worth it. Maybe a DH Otter
   would be better suited. How about a Twin Beech? Or a DC3 on Floats?
   Just mildly turbo charged. Don't throw those old DC3's away just
   yet.


   Paul Lamar

       Those are all great ideas but unfortunately all of those aircraft
   hold a
       type certificate.  You would never get the FAA to sign them off. The
       only place such a beast would ever get off the ground is in an
       experimental amateur built such as the TTC Harmon Rocket.

       Speaking of the TTC, how did you get an airworthiness certificate for
       it?  Did it already have one from a previous life?  With all the new
       modifications it surely must got through phase 1 testing before you can
       fly it outside of it's designated test area.  How are you dealing
   with that?

    Mark LaPierre

       All the required FAA paper work is handled. Took a couple of weeks :-)

       Paul Lamar

       Paul,

       I doodled something kind of like this while bored at work one day,
   only it
       was two three rotor engines, side by side, longitudinally mounted
   on one
       gearbox.  It could have an extended prop shaft with radiators in
   front like
       a FW-190 D or it could be fairly short so it could also go in a
   side by side
       type like the Lancair or Nemesis and fit the same envelope. With
   aluminum
       end plates, it might be lighter than the big, turbocharged six and
   put out
       around 700 hp, which is probably the upper limit of the horses most
   of us
       would want to feed.

       Steve Brazil

   Paul,

   Latest post on this tread, by Steve Brazil, I looked on past posts and I
   do not find the doodle he spoke of? Please if you can find his drawing
   send it on a future post.

   Lancair
   http://www.lancair.com/lancair-es-es-p-iv-iv-p/ <http://www.lancair.com/lancair-es-es-p-iv-iv-p/>

   Nemesis
   http://www.nemesisnxt.com/kit/p3-2.php <http://www.nemesisnxt.com/kit/p3-2.php>

   Thanks

   George F. Curtis Jr.

   That doodle is in pencil on my notebook at work, not on any program.  I was
   thinking of a two mesh gear set, with idlers to correct rotation and maybe
   allow an offset to improve packaging.  There would have to be room between
   the engines to provide clearance for manifolds on the right engine. Two
   three rotor engines could also deliver a lot of energy to a power recovery
   turbine.  There are some large homebuilts out there that are designed for
   either the Walter (GE) or PT-6 that could use this.

   Steve Brazil



Paul,

For some reason the drawing is not transferring along with the e-mail.

George F. Curtis Jr.

He did not attach it. It is in his notebook.

Paul Lamar

   The Rotary Engine free News Letter. Powered by Linux. If you want off
   the list PLEASE let me know and I will remove  you.  ACRE NL web
   site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
   Copyright 1998-2016 All world wide rights reserved.