Subject: Sachs rotary, charge cooled conversion starting
From: paul lamar
Date: 9/30/2016, 11:45 AM
To: A10-Me-Earthlink



    Ok, so today I took the time to take apart a Sachs 293 38hp rotary.

    I have attached some pictures. Now I saw and heard this engine running
    so I was surprised when i took it apart and saw metalset epoxy used to
    repair the inside surface where the apex seals run, also the entire
    engine case is made from aluminum. The only steel is used in the end
    plates where the bearings are.

    Anyway here are some pictures to look over. Ask questions if you want
    and i will do my best to answer them.

    David Mikesell


    Great pictures David.  Thanks.

    You can fix this by tig welding some aluminum on the bad spots and
    sanding them
    to shape.

    An oil squirter in the end house can cool the rotor with a pressure pump and
    scavenge pump or just an oil pan instead of the scavenge pump . A hose
    can run
    to a container under the engine and gravity will scavenge it.

    Close off the return passages for the charge cooling.

    Paul Lamar

    Well I was thinking of keeping the charge passages as a way for the
    cooling oil to drain from the engine. Those passages line up with the
    rotor cooling passages so oil will get slung out the charge passages on
    each side, plus they are the way the shaft bearings were oiled, I will
    use them as the oil return passages for the bearings. I will put the oil
    injectors just past those passages in the direction of rotation. That
    way the oil will get about 300 degrees of rotation to soak up heat from
    the rotor before it is pushed out the charge passages.

    My goal is not only to oil cool the rotor, with synthetic oil being
    injected on to it, but to water cool the engine also. I am sure the
    block is cast from A356 aluminum like most light weight engine blocks. I
    can get the dimensions from this one and design a new body with a bit
    larger outer dimension to allow for water cooling. And new end plates
    too for water cooling.

    I am going with 6061T6 and use my cnc mill to make the new parts. 6061T6
    is pretty close to A356 as far as temperature limits and strength. I can
    also get it coated with Niksal or another type of high strength and high
    temp coating. I think the first ones will be bare just for testing the
    set up to see if it works.

    David Mikesell

    You don't need them. The oil will find its way out through the way it
    came in.
    That is exactly the way the Mazda works.

    Where are you David? Tell me by private email if you wish?


    Paul Lamar

    San Jose, CA. Not far from Simon's shop, about a mile from my house.
    My shop is near San Juan Bautista, right off hwy 101

    How does the oil leave the block in the Mazda rotaries?

    David Mikesell

    It drains back through the center housing.
    Here are some  cut aways.


    Paul Lamar

What is the banana effect? I saw it the pointer it in one of the pictures.

David Mikesell

That is a theory that the hot side of the engine would expand more
than the cool side and looking down from the top the engine would
have a banana shape.

The serial cooling (AKA axial flow) was supposed to mitigate this but no evidences of
this happening  was ever detected. Probably because the steel tension
bolts on the hot side did not expand enough to detect.


  Unfortunately the rear rotor runs hotter than the front rotor due
to serial cooling. NSU used parallel cooling more of less. Both
rotors ran at the same temperature. All serious liquid cooled engine
have parallel cooling. No car engines!!! Car engines are all serial.

Max Bentele designed this when he was working for Curtice Wright.
Mazda copied it unfortunately.

"Max Bentele (January 15, 1909 - May 19, 2006) was a German born pioneer in the field of jet aircraft turbines and mechanical engineering. His contributions to the development of the Wankel engine  earned him the title, "Father of the Wankel Engine in the United States"."

Cylinder heads have the same problem. One side is hot and
the other side is cool. No one notices the banana effect.


Paul Lamar


The Rotary Engine free News Letter. Powered by Linux. If you want off
the list PLEASE let me know and I will remove  you.  ACRE NL web
site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
Copyright 1998-2016 All world wide rights reserved.