Subject: Sachs rotary, charge cooled conversion starting
From: paul lamar
Date: 9/30/2016, 4:25 PM
To: A10-Me-Earthlink

 Ok, so today I took the time to take apart a Sachs 293 38hp rotary.

 I have attached some pictures. Now I saw and heard this engine running
 so I was surprised when i took it apart and saw metalset epoxy used to
 repair the inside surface where the apex seals run, also the entire
 engine case is made from aluminum. The only steel is used in the end
 plates where the bearings are.

 Anyway here are some pictures to look over. Ask questions if you want
 and i will do my best to answer them.

 David Mikesell


 Great pictures David.  Thanks.

 You can fix this by tig welding some aluminum on the bad spots and
 sanding them
 to shape.

 An oil squirter in the end house can cool the rotor with a pressure
pump and
 scavenge pump or just an oil pan instead of the scavenge pump . A hose
 can run
 to a container under the engine and gravity will scavenge it.

 Close off the return passages for the charge cooling.

 Paul Lamar

 Well I was thinking of keeping the charge passages as a way for the
 cooling oil to drain from the engine. Those passages line up with the
 rotor cooling passages so oil will get slung out the charge passages on
 each side, plus they are the way the shaft bearings were oiled, I will
 use them as the oil return passages for the bearings. I will put
the oil
 injectors just past those passages in the direction of rotation. That
 way the oil will get about 300 degrees of rotation to soak up heat from
 the rotor before it is pushed out the charge passages.

 My goal is not only to oil cool the rotor, with synthetic oil being
 injected on to it, but to water cool the engine also. I am sure the
 block is cast from A356 aluminum like most light weight engine
blocks. I
 can get the dimensions from this one and design a new body with a bit
 larger outer dimension to allow for water cooling. And new end plates
 too for water cooling.

 I am going with 6061T6 and use my cnc mill to make the new parts.
6061T6
 is pretty close to A356 as far as temperature limits and strength.
I can
 also get it coated with Niksal or another type of high strength and
high
 temp coating. I think the first ones will be bare just for testing the
 set up to see if it works.

 David Mikesell

 You don't need them. The oil will find its way out through the way it
 came in.  That is exactly the way the Mazda works.

 Where are you David? Tell me by private email if you wish?


 Paul Lamar

 San Jose, CA. Not far from Simon's shop, about a mile from my house.
 My shop is near San Juan Bautista, right off hwy 101

 How does the oil leave the block in the Mazda rotaries?

 David Mikesell

 It drains back through the center housing.
 Here are some  cut aways.


 Paul Lamar

What is the banana effect? I saw it the pointer it in one of the pictures.

David Mikesell

That is a theory that the hot side of the engine would expand more
than the cool side and looking down from the top the engine would
have a banana shape.

The serial cooling (AKA axial flow) was supposed to mitigate this but no
evidences of this happening  was ever detected. Probably because the
steel tension bolts on the hot side did not expand enough to detect.


  Unfortunately the rear rotor runs hotter than the front rotor due
to serial cooling. NSU used parallel cooling more of less. Both
rotors ran at the same temperature. All serious liquid cooled engine
have parallel cooling. No car engines!!! Car engines are all serial.

Max Bentele designed this when he was working for Curtice Wright.
Mazda copied it unfortunately.

"Max Bentele (January 15, 1909 - May 19, 2006) was a German born pioneer
in the field of jet aircraft turbines and mechanical engineering. His
contributions to the development of the Wankel engine  earned him the
title, "Father of the Wankel Engine in the United States"."

Cylinder heads have the same problem. One side is hot and
the other side is cool. No one notices the banana effect.


Paul Lamar


Paul,
I have my first of 3 OMC 45 hp engines apart - This one was seized and
damaged the outer housing - Sort of a learning experience - In the back of
what passes for my mind I'm thinking about using my CNC equipment to make
new parts including the housing - Would be interested in communicating with

David Mikesell, off the list if possible, to swap some CNC programming
details that may not be of interest to the rest of the folks -

Roland Friestad

I am interested. There are several people on here that have CNC machines.
However if you want to keep it secret that is OK.

BTW I just re-read Max's rotary chapter in his book  and he increased the water velocity in
the hot areas around the lower spark plug with small holes in
the passages.  You can see them in this picture of a Mazda rotor housing.
According to him that carried away the nucleate boiling air bubbles.

Mazda used most of what CW developed and incorporated their own
developments.

I can't wait until some one tries oil squirter's on a charged cooled engine :-)
Great things will happen as you are starting with cool oil and
not warm oil that has already gone through  part of the engine.

Here also is the mechanical info on glass filled Teflon.
What would be even better for apex seals  is carbon fiber filled Teflon.

Paul Lamar

The Rotary Engine free News Letter. Powered by Linux. If you want off
the list PLEASE let me know and I will remove  you.  ACRE NL web
site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
Copyright 1998-2016 All world wide rights reserved.