Subject: Sachs rotary, charge cooled conversion starting Part 2
From: paul lamar
Date: 10/4/2016, 3:12 AM
To: A10-Me-Earthlink



 Hey Paul, ok so I took apart my second and third Sachs 293. One was
 totally seized, the second was not but again inside was damaged as if
  some type of debris found its way inside while the engine was
 running.

 Now both of these have a super thin steel lining in the main block.
 The end plates do not, all the end plates are just aluminum.

 The seized engine the rotor was locked into place, basically I had to
  beat the engine apart damaging a lot of parts. However there was so
  much corrosion in the main housing the thin steel lining has come
 off in places. The ballpark thickness is around .020, the thinnest
 was .014 and the thickest was .032 .


 So now we know lots of heads and complete engine blocks for piston
 engines are aluminum, usually 356 alloy because of the high silicone
  content that allows lapping it down to make a hard silica surface
 for the rings and such to ride on. Some use high flame coatings that
 are super hard. Some use Nikasil coating. In fact it was used by
 other auto makers when developing their rotary engines instead of the
 steel liner used by Mazda. It is a really hard coating but it can be
 expensive.

 I do believe I will bit the bullet and have my new housing Nikasil
 coated. Well, unless we can come up with something cheaper, that can
  take the wear and the heat.

 We could use a hard anodized finish for the side/end plates is we are
  able to use the Teflon/carbon fiber side seals.

 Now need to think of a material to use on the rotor apex seals that
 :

 1- will  [not] dig into the aluminum housing

 2- that will not gall the aluminum or weld the aluminum to the apex
 seal itself.

 3- that can withstand the combustion and exhaust port temperatures.

 Now I do not remember where but I had seen a statement that the apex
  seals perform really well at low speeds but are not a absolute
 necessity at high speeds. If this is true then the seals could be a
 type of high temp plastic that can withstand the pressure of
 combustion. One critical thing that has to be thought about is the
 peak temp as the seal passes the exhaust port and the flame passes a
  small portion of that apex seal at 900 to 1200 degrees F. The
 exhaust port could span more of the chamber but then you could get
 greater seal wear going over a long oval port vs a rounder port.

 If we have to make them from a high temp metal then we have to be
 very careful of the seal shape to lessen the chance of galling or
 gouging the aluminum housing. To me this would mean a wider seal face
 or less seal pressure, or a combination of both.


 David Mikesell

 Fantastic information David thanks.

 What are the dimensions of the Sach's Apex seals?

 You might be able to use cut down 12A Mazda ceramic or cast iron
 seals.

 That is REAL interesting about the thin steel liners. That would be
 relatively easy to duplicate. They could be chrome plated with out
 much cost. They are trapped in  there.  They could be hard enough to
 act like a spring. Squeeze them in at the waist to install them.

 Sort of snap in place. Small buttons, or tiny hills  would or could
 be used to lock them in place. This has some thermal heat loss
 advantages. The way Mazda does it is actually not as good thermally.
 Too much heat is transfered to the aluminum.

 Also long small diameter screws could be screwed in from the out side
  into small metal bars welded to the thin steel sheet around the hump
 area to hold them in place.

 Kind of funny I did not know about that. Thin hard stainless steel
 might work as well. Even less heat transfer. Same for the side
 plates. Thin SS side plates could be water jet cut and be the cheese
 in the sandwich :-). Much much cheaper to repair.

 Doing away with the charge cooling will improves the volumetric
 efficiency up to 20 to 30% which translates to 20 to 30% more HP and
 a lower BSFC. We might just come up with a world record low BSFC for
 all Wankel engines.

 BSFC is pounds  of fuel burned for each HP generated.

 Currently it is .47 for the leaned Mazda while a Lycoming is .45. The
  Cont. engine in my C182 is as bad as .52. If we can get it down to
 .46 that is a HUGE reduction in the history of rotary BSFC's.

 Currently the BSFC for an air cooled Austro Engines one rotor is .52
  to .55. Higher for all charged cooled engines. Over .6x for the
 OMC's.

 All turbo props are over .65 and as bad as 1.0 !!!!

 Seems the thermal heat loss thing was the last thing on Kenichi
 Yamamoto  mind when he designed the Mazda. He just wanted it to
 work.

 Paul Lamar


There is no where near enough silicon in 356 aluminum to allow a piston/ring to run directly on the bore material.  You may be thinking about 390 which will work under those circumstances. However, an aluminum piston must have a coating to survive in an 390 aluminum bore.
Nikasil or plasma coatings will allow a plain piston to be used.

Gary Knutson

Hi paul,
   If you did use stainless liners, the heat transfer would be less, right, well maybe you could use a high temp glue to hold in the liners. Even if the glue failed in the hot section there would be still enough glued area to hold it in place.
   Chris Hoskins NZ

Teflon is a glue and it melts over about 550 to 700 F. I don't know how to
work with it.

Think of a male figure eight made out of thin springy material.
If you squeeze it in the center it will get smaller. It will then
fit in a solid female figure eight that was the same size as the
original male figure eight. When the squeeze is release it will lock itself
into the solid female figure eight. A trochoid is close to a figure eight.

You might have to squeeze it  a bit the long way as well

Made from hard sheet metal (SS or Steel) bent into a trochoid and seam welded.
Low cost  to over haul and low cost to manufacture.
Chrome plated to keep the heat in the combustion chamber

Patent Pending :-)

Paul Lamar

The Rotary Engine free News Letter. Powered by Linux. If you want off
the list PLEASE let me know and I will remove  you.  ACRE NL web
site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
Copyright 1998-2016 All world wide rights reserved.