Subject: apex seals and side seals
From: paul lamar
Date: 10/5/2016, 9:20 AM
To: A10-Me-Earthlink


    Hi Paul, what is the best way to get the seals on the rotor, Apex
    seals,   side seals  out without damaging them. The ones in this old
    sachs rotor are stuck and I don't want to tear apart to get them
    out.

    David Mikesell

    Soak it in solvent for 24 hours. Gasoline or MEK or acetone or even
    kerosene. For some strange reason auto transmission fluid sometimes
    works.

    BTW the Sach is a good engine to do R&D on apex seals. Try glass
    filled teflon. Back in the days Mazda was doing research on the
    subject that was not availably.

    The oil squirter should keep the rotor temperature well below 500 F.

    Perfect for the side seals as they run nowhere near the temperature
    of the apex seals.

    Paul Lamar


    Well I plan on using the addition of the oil squirter so I can bring
    the temps up to get more hp out of it.

    You think the glass filled teflon will work for apex and side seals?
    I would think it might get wedged or stuck in the slots. I would
    guess even though it is glass filled still a bit soft though.

    If it would work that would be nice to have a all aluminum housing
    that will last with nice affordable seals that will last too.

    David Mikesell

    This carbon filled Teflon is looking great. I suspect the aluminum
    side housings can be simply anodized and that is it. Much cheaper
    than any type of flamed sprayed coatings.

    Paul Lamar


    Hi Paul and all, a friend of mine here in OZ has just supplied disk
    brake rotors to the navy made from 6061 T3 with a hard anodized
    coating that is rated at 800 Brinell, which is about 85 Rockwell.
    This makes it about 2 times harder than cast iron. Should be fine
    with a lubricated rotor running over it, especially with carbon
    filled Teflon seals.

    He did point out that to get a good anodized surface, 6061 T3 is
    needed as the surface will not finish well with cheaper grades due
    to impurities in the alloy.

    So, I think that means we must mill the housings from billet. FWIW,

    Dave Mccandless in OZ

    Well we are planning on  milling  the housings from billet. No
    castings. The RB's are castings.


    Paul Lamar


    The carbon filled potential nylon probably won't work. In the
    literature it says it will hold up at 900 fpm and up to 2500 psi
    non-lubed and 3500 psi lubed. The distance around this small rotary
    housing is more than a foot, so the limit would be 900 rpms.

    David Mikesell

    Not the apex seals. The side seals go about 1/3 rd as fast in a
    complex rotating and translating pattern.

    And Teflon "glue" not nylon. Nylon is only good to 200 F. Teflon is
    good to 500 F

    Still worth a try for side seals.

    There is no beating a silicon nitride apex seal except for the cost.
    Since the rotor is rotating even the apex seals do not rub at 900 fpm
    at 900 RPM. Something less.


    Paul Lamar

    I wonder what the Apex and side seals are made from in the Sachs
    rotary.

    With the housings being all aluminum and hardly any scoring marks,
    except for the damage caused by something getting inside with the
    rotor, the surfaces look pretty good.

    David Mikese

    Me too. They look strange.

    Paul Lamar


    I got it wrong, the alloy is 6061 T6     not T3

    Dave Mccandless in OZ


   Diesel works amazingly well to remove carbon... might even try oxalic acid for rusted together parts....or CLR...

   Dan Gorsline.

I have been involved over the years in salvage and restoration of old hit and miss and one lung diesel engines. We have been amazed
at how well JET B works. It seems very corrosive, and the rust just falls away. Warmed up it finds it way into every crevice, and a few days
later the parts undo fairly easy !

Steve Carlisle




The Rotary Engine free News Letter. Powered by Linux. If you want off
the list PLEASE let me know and I will remove  you.  ACRE NL web
site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
Copyright 1998-2016 All world wide rights reserved.