The engine is lost in the cowl :-)

 I think I'll put a huge muffler in there :-)

 I have some more ideas on the cooling baffles. Do away with at least
 one :-)

 Paul Lamar


 That looks great  with all that room.  I think it would be ideal for
 fitting to my Barber Snark  although I would only need about 105 HP
 as that would easily allow me to exceed VNE of 140Kn. You mention
 making the body out of block of steel but what grade of steel would
 be best and what would you estimate machining cost at? If more that
 one off to be done would it not be best to rough cast the shape and
 then finish of with the NC machine centre allowing some flats for
 the heat sinks. If the price to build is low enough you would be able
 to compete in the drone market as well as small aircraft. If enough
 rotary enthusiasts go together they could form a viable engine
 company.

 Colin Dale

 You don't have to open the throttle all the way.

 Here that cooling idea I had. Works well for the top heat exchanger.

 We need an experienced corporate  CEO.

 Paul Lamar


 Greetings, Paul For the past several months I have been searching the
 internet for all things pertaining to rotary, in an effort to prepare
 a start up business plan, producing rotaries to satisfy a substantial
 angel funder.

 The intended market is, ultralight high power motorcycles, off grid
 energy and of course aviation.

 We are seeking a highly experienced over qualified aeronautical
 engineer and mechanical/machine shop owners to negotiate coming on
 board to finalize engine physics and production processes. Initial
 single rotor Engine sizes: 5hp, 30hp, 50hp, 100hp. (Much larger multi
 rotors to follow)

 Proprietary Compound turbo exhaust energy recovery systems capturing
 kinetic and heat  energy are a paramount requirement.

 It has so far been determined that an engine based on a forged hard
 chromed chromoly ring overlaid with a carbon fiber honey comb filled
 with ceramics. Finished for strength/final shapes automatically
 wrapped in sufficient layers of carbon fiber material by high
 pressure molding technics will likely to produce a highly
 efficient,light weight affordable product. Respectfully awaiting your
 questions/responses. Thank you,

 Michael Nash

 Staunton, Virginia

 You are on the bleeding edge there. You won't save a lot of weight
 in the overall product. Make the rotor housing out 4340 or 4130 and
 let it go at that. It only needs to be 1/4 inch thick roughly. Add
 aluminum heat sinks as necessary. That is a much easier R&D program
 to fine tune the thermal characteristic.

 Is Staunton Miltary Academy still in Business? Fork Union used to
 play foot ball with them. I went to Fork Union.

 Paul Lamar

4130 was the ticket. I agree air cooled works best for the 2 small
engines. Nice kiss.
A couple Aixro xr 50's with H2o/Al injection added will be put into a
couple Kawasaki 250r's  near twice the hp and torque. Just for fun and a
test bed for exhaust development. Just got air flow numbers from them
this morning.

SMA closed and now is a museum/retreat according to the signs.
Thank you,
Michael Nash

Fork UInion is struggling as well. The middle class is disappearing.


Paul Lamar


For a rotor housing, would it be possible to start with a large OD thick
wall pipe
cut to approx rotor width then deform it to a rough housing shape using
a hydraulic press?

Robert LeClercq

If that works that  would save a lot of money.
Maybe heating it first to make it easier to form.

Please research thick wall pipe for us.


Paul Lamar



Paul

Here are a few:
http://specialtypipe.com/home/products/large-diameter-seamless/
https://stainlessandalloy.com/stainless-steel-seamless-tube/
http://specialtypipe.com/home/products/large-diameter-seamless/?gclid=CJzRz_3DkNACFQgpaQodKKkEBQ
http://www.pennstainless.com/stainless-products/pipe-and-tube-stainless-steel-products/stainless-steel-seamless-pipe/

Stainless and hot rolled steel are available as seamless too.
OD and wall thickness will be determined by how closely the deforming comes to the desired trochoid shape. I suppose after bending that annealing would be required.
Mazda inner circumference is 27"+/-. So about 8.5" tube ID.

Robert LeClercq

That sounds reasonable. Thanks Robert.


Paul Lamar

The Rotary Engine free News Letter. Powered by Linux. If you want off
the list PLEASE let me know and I will remove  you.  ACRE NL web
site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
Copyright 1998-2016 All world wide rights reserved.