Subject: 650 HP TTC injector holders are done.
From: paul lamar
Date: 12/17/2016, 2:00 PM
To: A10-Me-Earthlink


My Morse taper gave out when drilling  brass  on my CC lathe. The
drill digs into the brass and then the taper slips. It took me hours
to drill a 2 inch hole in the 3/4 thick aluminum bar shown keeping
the taper chuck from rotating. It holds when drilling  aluminum or
steel.

The reason for the brass interior part was because aluminum would
generate yellow snot when flowing methanol.

These injector holders are high precision. The adjustable 3 jaw chuck
on my CC lathe was under a 1/2 thou run out. This design would not be
possible with out that.

Basically it is built around 37 degree flare fitting AN-6  to 1/4
inch pipe steel adapter from McMaster Carr. Under $3 each. And 5/8
diameter brass rod insert. That had to be machined down as the
diameter tolerance was all over the lot.

In terms of hours of engineering, design and machining at $50 an
hour they are worth well over $500 each :-)

The tiny drilled head SS 6-32 screws are also from MacMaster. This
was a precision operation as well as the hole depth for the screws
was limited to exactly .2 inches or one would have a 150 psi leak.
There are only about 6 threads in the hole. Once they are safety
wired they just act as retaining pins. The mechanic better go easy
with the screw driver :-)

The .040 aluminum straps holding the whole works together are not
shown. They will be tig welded to the large intake tubes.

This 200 pound 2 rotor engine is generating  650 HP with only four
injectors. PAC in Oz used eight for some strange reason. Maybe they
have not heard about the Bosch 2000 injectors :-) Maybe that was for
a 4 rotor.

Paul Lamar

It's probably not the Morse taper that was the problem - More likely
you were using a drill ground for steel - For brass you need slightly
different angles on the drill point and that problem goes away

Roland  Friestad

I did not know that Roland, Thanks for the tip.
I at first thought it was the 13 mm drill bit I paid $40 for.
Then I bought a 39/64th for $40 and that was only a bit better.
I never saw a brass drill for sale.

Is there any way to fix the male taper on my taper chuck? It is scarred
up pretty bad. Must I buy a new one. Hopefully the taper will be harder.

Paul Lamar


If the Morse taper is scarred up then it is likely that the socket in the
lathe is also scarred up - Fixing it is certainly possible but requires time
and careful workmanship - Check the lathe socket by running your little
finger in the hole and check for internal scarring - ANY internal scarring
means that fixing the Morse taper unit or buying another one will be a bit
of a waste of time and money until the lathe socket itself is fixed -

There is an excellent book, "Machine Tool Reconditioning" available from
Industrial Press that is sort of the Bible of the industry - The drill point
angles for brass are available in one of the other industrial Bibles, Mark's
Handbook or the McGraw Hill series of 9 volumes (Don't remember which
volume)

Reamers for repairing Morse taper sockets are also available as a commercial
item - Lathe tail stock sockets are not usually hardened, at least in my
experience, so a reamer might be the best way to go - Don't know much about
what you call a "CC" lathe - Is that a brand or some sort of abbreviation ?

Following is a blatant plug --- Go to www.digitekbooks.com  -  I am setting
up that website to provide digital copies of shop and engineering books at
reasonable prices - Sort of like an electronic version of the old Lindsay
reprints -

Sorry to intrude with crass commercialism here but I and engineering and
aviation friends of mine are attempting to preserve some of this old
information - Between us we have several thousands of technical books and
manuals to preserve and make available - Website is just getting started -

Thanks for all the Wankel information - My OMC snowmobile rotary engine
project is lurching along slowly - About to begin disassembly of the two
running engines now that the seized engine has been disassembled as a
learning project -

Roland Friestad

Thanks for the great tips Roland. I'll find a copy of the book and buy it.
I have Marks hand book already but I am really bad at regrinding drills.
I need some sort of device to help me do that.

CC stands for Cheap Chinese :-)

Paul Lamar Merry Christmas

The Rotary Engine free News Letter. Powered by Linux. If you want
off the list PLEASE let me know and I will remove  you.  ACRE NL web
site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
Copyright 1998-2016 All world wide rights reserved.