Subject: The data from the TTC runaway turbo with the manual waste gate.
From: paul lamar
Date: 1/18/2017, 7:34 PM
To: A10-Me-Earthlink


It looks like we got ten seconds to back off  when the throttle is
100% before the manifold pressure runs away to infinity :-) This is
at 245 feet above sea level.

When you arrive at 100% throttle the manifold pressure is  50 inches
of Mercury (Hg) and builds up rapidly to  52 or 53 inches of HG. Then
of course it shoots up 80 inches of Hg or above. Runaway.

It is so remarkable  that an all aluminum 200 pound  Wankel Mazda
engine generating 650 HP will tolerate this. A piston  aircraft
engine  would blow up and kill you with shrapnel. A good size bomb
going off.

The Motec is trying to open the waste gate  (if it were there)
slamming it back and fourth 50% full on and 50% full off.

The Lamda on this run was .751 which is  11 to one air fuel ratio.
Quite rich but this is methanol.

Normal for methanol is .83 which is 12.2 to one which is about the
same for gasoline at full power.

This is with a one inch hole in the bypass exhaust pipe. It does not
runaway with the stock 1.25 inch hole under static conditions. Dan is
going to fly it with the stock 1.25 by pass and see if it runs away
away when the engine RPM climbs to 8,000.

At that point we can add another parallel waste gate with a spring
set to 26 inches of boost or make the hole in the bypass aperture
larger. Say 1.3 or 1.4 inches in diameter up from 1.25 inches.

Here is an inches of Hg to boost in psi conversion chart and the
program used to generate it. Plus the start video.

Paul Lamar



Paul,

According to Heywood, the AFR of methanol is 6.5:1.  Are you using
pure methanol?  How did you come up with the 12:1? Attached is a
table of common fuels, their associated metrics, and a simplified
method of calculating AFR. Aaron Buster

Research Engineer Advanced Powertrain and Emissions Spark Ignited
Engines R&D Department Southwest Research Institute


According to our Motec expert to convert from the mixture decimal
number recorded in the Motec to a mixture ratio you multiply times
14.7.

The other thing is if it were really 6.5 :1 based on volume you would
go through a 20 gallon tank of Methanol really fast at 650 HP. We ran
it for at least 26 minutes on 20 gallons. Therefor I doubt that is
the correct mixture ratio.

Paul Lamar

You are right! There is something wrong with that mixture number.

We ran it again this morning. More on this later.

Paul Lamar

It is important to always be rich on methanol.
Murry Rozansky

Yes I know that. The question is how do you convert a decimal number like .743 out
of the Motec to a conventional mixture ratio? Like 12 to one or 14 to one?

The conversion is in question. Not the number.

We ran it again this morning and Dan wants a blow off valve on the intake
manifold set to 20 inches of boost. So that is in the works. This is the one I have
chosen.

Paul Lamar

Start with stoichiometric or lambda for methanol. Part of the issue is that alcohols have an extra oxygen atom gasoline does not have. They also have less hydrocarbons to react with the oxygen atoms.
They do have an advantage in detonation resistance so higher compression ratio or boost pressure can be used.Similar to running on propane, you will experience poorer fuel economy unless you build an engine with 13:1 compression. Natural gas can run 15:1.
Using a BOV on a turbo engine is a definate safety requirement, just in case the wastegate fails.
Dale Davies

What is the stoichiometric or lambda for methanol ratio?
Perhaps that is what is what is to be multiplied by the Motec mixture decimal number.


Paul Lamar


The Rotary Engine free News Letter. Powered by Linux. If you want
off the list PLEASE let me know and I will remove  you.  ACRE NL web
site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
Copyright 1998-2017 All world wide rights reserved.