Dan found room between the fuel tank and the side of the aircraft to
fit the waste gate control cable in. It gave us more precise
control over the waste gate opening with a much longer lever.
Worked like a charm. The max boost was limited to about 15 to 20
inches. That is about 50 to 70 inches of HG.
So we said "lets see what happens if we make the 1.25 inch bypass
aperture smaller." We then tried a .8 inch diameter and the turbo
ran way. More eng RPM more boost more eng RPM more boost and so on.
Mathematically it is an exponential function. It started dragging my
4000 pound truck in park :-)
Dan jerked the throttle back.
We then tried a 1 inch aperture. It still ran away at RPM and high
boost.
This is at sea level of course once you get up to several thousand
feet things will change.
Here are some pictures.
We need to go back into the Motec and reset the mixture. Does
anybody on here know how to convert Motec mixture numbers like .7 or
.8 to a mixture ratio like 14 to one?
It starts as easy as my RX8. Smoke for a few seconds on start up
but that is normal for a turbo charger.
Paul Lamar
Is that 15 to 20 inches water, Hg or PSI? Should be Hg or PSI as Hg
would give the 70 inches water. I forget the conversion.
Dale Davies
I get confused some times. The Motec is a mishmash of measurement
systems. Imagine calling a pressure with a persons name. That is why
they call a pressure pascal's in the metric system. REALLY
STUPID!!!!!! It is a force divided by an area for @#@## sakes. PSI or
Kilograms per square meter is intuitive.
I am surprised they don't call Miles Per Hour or Kilometers Per Hour
Napoleon's :-)
The linear measurements are OK with mm, meters, kilometers doing away
with inches, feet and miles. All arbitrary measurements. However one
could say micro, milli, mega and giga inches.
The latest is converting a ratio to a decimal number. Really stupid.
Yes 14.7 is the ratio of air to fuel that results in a complete
change. Now we have .73 mixture.
We have boost in psi, inches of Hg (the aircraft engine standard)
pressure and heaven forbid microPascals. 30 inches of Hg is roughly
atmospheric pressure at sea level. So is 15 psi. So you can see the
conversion problem. It extends to pressure measuring devices.
Manometers are very low cost and very accurate devices with inches of
water and inches of Mercury (Hg). There are absolute pressure gages
and gage pressure gages. Inches of Hg is absolute while boost in psi
is gage pressure.
The metric system has thrown the engineering world into chaos. It
would have been better to keep furlongs per fortnight alone and
forget the metric system :-) My late great rocket scientist and
experimental aircraft designer friend, Vance Jaqua, was fond of
saying we got to the moon on inches.
After all Sir Isaac Newton was English. It is not for nothing that
they call it Newtonian Physics.
I can understand why nobody wants to study engineering any more. It
is taught in the silly metric system. One goes into the lumber yard
and sees 2 by 4's and nuts and bolts in inches.
Paul Lamar
Hi Paul, Both systems of measurement have their idiosyncrasies, it
all depends on what system you are used to (what you grew up with). I
mean what could be more stupid than the Fahrenheit temperature scale,
water boiling at 212 deg instead of 100 deg and freezing at 32 deg
instead of 0. If you say (and I agree with you)it is stupid to use
somebody's name for a scale of some sort, it is no more stupid than
using some English kings foot measurement to be called a foot and
divide it into 12 instead of ten, (we have TEN toes and fingers) a
yard is the length of his arm etc, I shudder to think what the 6 inch
measurement comes from. At least in metric everything is in tens.
Chris Hoskins.
I agree on decimals. Micro, milli, mega and giga inches :-)
I think the inch was the distance from the King's thumb knuckle to
the end of his thumb :-) Why water? Why not oil. After all they
boiled the bad guys in oil those days :-)
Something has to be a standard. I think the meter has something to do
with the diameter of the earth.
The strength difference between a 10 mm bolt and an 8 mm bolt is
enormous. The 8 is something like 64% as strong as a 10 mm bolt. I
have never seen a 9 mm bolt. Fraction of an inch bolts are much
closer. The weight of a device will be lighter if fraction of an inch
bolts are used and just strong enough is chosen..
Paul Lamaer
I don't know for sure, but I think the English measurement system made
sense for yesteryear because it is very easy to geometrically divide a
line segment in two with a compass: 12, 6, 3, 1-1/2 (or 3/2), 3/4, 3/8,
3/16... or whatever the tolerance is of your axe; something an average
peasant can do.
I'm not sure tenths is as easy...
Chris Cosman
The Rotary Engine free News Letter. Powered by Linux. If you want off
the list PLEASE let me know and I will remove you. ACRE NL web
site.
http://www.rotaryeng.net You Tube
http://tinyurl.com/beqqxas
Copyright 1998-2017 All world wide rights reserved.