Subject: Mazda and Curtiss Wright worked together.
From: paul lamar
Date: 1/19/2017, 8:43 AM
To: A10-Me-Earthlink



" Maybe in Oz you can find 9 mm or 7 mm but not in the US.
A even bigger difference is between 6 and 8 mm.

The early Mazda rotaries were designed in inches but they did not use inch bolts.
This is because they were copies of CW rotary engines I suspect."

Paul Lamar

Hi Paul,
your comparison is again not fair.
6mm should be compared to 1/4 (6.35mm). 7mm bolts are available in the auto parts stores, I had an Alfa Romeo that had 7mm bolts holding the inlet manifold; never seen a 9mm bolt, they are rare!
I find it hard to believe that a NSU rotary from Germany and adapted by Mazda was designed in inches.
Interesting subject,

Dave Mccandless in Perth

A German guy that worked for Curtis wright invented the serial cooling system which Mazda used.
NSU used a parallel cooling system.

His name was Max Bentele. The book was called Engine Revolutions. It was mostly an Auto Biography.
Chapter 8 was about his time at Curtiss Wright. He was working at Curtiss Wright when he first
heard of the rotary in May 1958. Curtiss Wright later had the exclusive rights in North America. No matter where
they were made. Reported to have the nick name in the US as Mr. Rotary.

"We attacked with fundamental investigations the engine's problem areas, the structure and cooling of the housings and the rotor, the main bearings, and the oil and gas seals. The latter posed a dilemma. The NSU/Wankel gas sealing network was a Swiss-watch type, theoretically 100-percent effective but hardly practical and durable. Wankel being admired as the gas sealing expert, we were obliged to copy his design to the last detail for the time being.

Cooling of the trochoid housing presented the greatest challenge. In a reciprocating engine, cylinder head and piston dome are exposed to all phases of the working cycle. In contrast, the individual portions of the engine outer housing are exposed only to their respective phase. Temperature and flow velocity of the working medium, and thus the heat flux to the housing wall, vary along the trochoid circumference. Two extremes exist: In the combustion zone, the very high heat flux will induce nucleate boiling of the cooling water; in the intake area, the inflowing fuel V air mixture is, due to fuel evaporation, colder than the ambient atmosphere and much colder than the cooling water. The design task was therefore twofold: (l}to prevent overheating and resulting thermal cracking of the housing in the combustion zone and (2) to minimize thermal distortion of the housing and to assure effective gas seal operation.  [that was a problem with the NSU Spyder engine]

We soon realized that NSU's circumferential cooling flow was incapable of fulfilling all requirements of high-performance engines. We selected axial flow, back and forth between the side housings, with the flow velocities in the various rotor housing sections adjusted to their respective heat input. In the combustion zone, the high-velocity cooling flow removes the steam bubbles generated by nucleate boiling, and thus permits extremely high heat fluxes to the housing without detrimental effects. This cooling scheme was also beneficial to the structural integrity of the rotor housing. Engine test runs confirmed its effectiveness in all respects. It was patented and became the standard for all high-performance Wankel engines.

NSU's experimental engines incorporated anti friction ball and roller bearings exclusively. According to our life prediction analyses, this bearing type was inadequate for our purpose. Consequently, we used sleeve bearings for the rotor and power shaft. (NSU also finally had to abandon anti friction bearings.)

In addition to these basic design investigations, we studied the porting and timing of the air and gas flow as well as geometrical effects such as the ratio of the trochoid generating radius to its eccentricity, the housing axial width relative to its axes, and other parameters. "

Page 57

Many of these developments where published in SAE papers in the 1961 SAE transactions.

This was in 1958. However Mazda Licensed the engine directly with Felix Wankel in the summer of 1961.
Mazda really perfected the sealing system. Especially the oil seals on the side of the rotors.

Paul Lamar

The Rotary Engine free News Letter. Powered by Linux. If you want off
the list PLEASE let me know and I will remove  you.  ACRE NL web
site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
Copyright 1998-2017 All world wide rights reserved.