Subject: RD-1c question Tracy Responds
From: paul lamar
Date: 3/10/2017, 6:53 PM
To: A10-Me-Earthlink


 Paul, do you or anyone on the group remember the change in crankshaft
 resistance after torquing down the RD 1C 12" an4 bolts at final
 assembly?

 The assembly instructions show a trial fitting without the 5 1/8 inch
 ring gear spacer o-ring. This worked well on my unit, with the
 crankshaft turning easily by hand.  However I found this "O" ring was
 missing from my unit.

 Tracy's specifications are for a 5 1/8 inch outside diameter and
 0.190 inch thickness, which  corresponds to an AS568-351 (3/16"
 thick). I ordered some of these,  but found that the actual thickness
 is 0.21 inches, not 0.190". I cannot find any metric or other
 equivalent size that exactly matches the 0.190 specification.

 When tightening down the drive bolts to the final torque, the
 resistance to turn the crank shaft roughly doubled. I can still
 detect just a little bit of backlash play, but the torque required to
 turn the crank shaft without spark plugs installed is approximately
 20 foot pounds.  It appears this is due to the resistance of the ring
 gear pressing on the O-ring against the adapter housing.

 Does anyone know if this amount of resistance is normal, or perhaps
 Tracy was using some o-rings that are exactly 0.190 inches in
 thickness?

 Thanks!

 Scott Gettings


 I assume that is the late  one that does away with the torque
 damper. I have no experience with that one. Send me a dwg or sketch
 if you can. A picture or two would also help.

 Typical of O-ring dimensions. It gets real critical when you are
 dealing with the rotor housing O-rings. Too big and it will crack the
 cast iron.

 I this case it's not that bad.

 Paul Lamar


 The RD1 C still has the 4-bolt damper that mounts to the flex plate.
 I added AN 970 large washers to the bolts on the engine side to the
 plate, which was obviously highly stressed by the bolts and standard
 washers on that side. It is also easy to inspect.

 I have attached the expanded view of the RD1-C.  The ring gear has a
 45 degree cut on the outer circumference to accept the o-ring. The
 oring just pushes against the solid adapter cylinder (the part that
 bolts directly to the adapter plate), thus keeping the ring gear
 tight.  It seems this oring spins against one or the other surface
 when running.  So when trial assembling without the oring, the gears
 spin freely.  With the oring in place, there is pressure on the ring
 gear as the bolts torque down.

 Here is the scan and adapter pix.

 Thanks, Scott Gettings


 The ring gear is stationary. The bulkhead the ring gear splines on
 is bolted to the gear box case. Nothing critical about that O ring.

 Those bolts are flat heads screws. The early ones where known to
 shear. I think the diameter was increased in the later versions.

 The stock Ford bulkhead is powdered metal and SUPER hard. Makes a
 good bolt shear :-)

 Old message:

 "I found that seven (7) of the eight (8) 1/4-20 bolts holding the
 ring gear to the casting were broken.  Only one bolt was still in
 tact, and it was loose.  After discussing this with Tracy, we agreed
 to drill and tap them to 5/16-20 which I did. "

 Please take one of those screws out an measure the diameter for me.

 After you fly it for a few hours  it disassemble the gear box and
 check those bolts that bolt the ring gear bulkhead to the gear box
 case.

 Paul Lamar



 Will do.

 Scott Gettings

Paul,

I opened my RD1-C drive, and have included some pix.  The ring gear is
on a splined shaft connected directly to the prop hub.  It is not fixed
to the case and does not have  the  screws mentioned above. The ring
gear can easily be pulled out, as per the pic.  The planet carrier is
fixed to the “spacer” part of the RD case (against the flat adapter plate).

You can see the location of the o-ring.  When in place, it sticks up
about 0.03” before compression.  Since the surface on the spacer/planet
carrier where the o-ring contacts is rough (see pic) , it appears that
the ring gear must rotate along the fixed o-ring surface.  There is
nothing else other  than the o-ring holding the ring gear from impacting
the  prop side of the  planet carrier.

Turning the engine over without compression requires about 10 ft-lb of
torque.  When the  o-ring is compressed, this doubles to about 20
ft-lbs.  Do you think this is an acceptable amount of drag?

Thanks again?

Scott Gettings


 Aw so my mistake. I thought all C versions were 3.12 to one. You have
a 2.12 to one I think.
Power is out of the ring gear rather than the planet carrier as in a 3-2-1.

An O-ring used in that fashion is very very unusual to say the least.
That is not what they are designed for.

Maybe Tracy did that to dampen some vibrations. I have NO idea what he
was thinking :-)

Paul Lamar


Paul,
  Sent this question to Tracy and his reply is below........

Tracy,
 The post below was sent to Paul Lamar by Scott Gettings.........Perhaps you can
shine some light on his problem ??............I was not aware the "O" ring was used
on the 2.17 version of your redrive...........The initial thought was Scott's redrive is
a RD1C but photos show it to be a RD1B........If you do not have Scott's E mail
send your response to me and I will forward it.........Thanks

Best Regards,

Kelly Troyer


Kelly Troyer

You are right Kelly, the RD-1B does not use that O-ring.  That’s only for the -1C version.   Not surprised the drive would bind if he tried to use one on a B.

All the best,
Tracy


The Rotary Engine free News Letter. Powered by Linux. If you want off
the list PLEASE let me know and I will remove  you.  ACRE NL web
site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
Copyright 1998-2017 All world wide rights reserved.