Subject: Tach adopters finished.
From: paul lamar
Date: 3/15/2017, 1:07 AM
To: A10-Me-Earthlink



      David,

      Here are all three tach adapters finished machining. Took about 8
      hours per adapter.

      I was rather surprised to see two contactors wired in parallel. It
      appears to be the 3 phase for the knee motor. That huge motor can
      probably lift 500 or 600 pounds.

      I guess back when the Kasuga was built they did not have contactors
      with enough current.

      "A contactor is an electrically controlled switch used for switching
      an electrical power circuit, similar to a relay except with higher
      current ratings and a few other differences A contactor is
      controlled by a circuit which has a much lower power level than the
      switched circuit."


      I have a new invention I will upload shortly for simplifying some of
      this rat's nest :-)

      Paul Lamar


      Looks great. I switched to solid state relays, use 5vdc data to
      control, no contractors to have carbon Build up or wear out.

      David Mikesell San Jose California

      Is the idea to turn off all circuits if a limit switch opens some
      where?

      So all limit switches are in seres? What would the schematic look
      like?

      I am thinking of a Maxmite and a LED panel that tells you which limit
      switch opened.

      Or is that feature built in EMC ?  Is it in Mach 3 ?


      Paul Lamar

      You can put all limit switches in a series So if  anyone of them
      opens it goes into e stop, or if it's in homing it takes that as a
      limit to whatever axis was moving. It works that way in mach3 also
      EMC. I personally wire each one individually as an individual home
      switch and it also acts as a limit switch. And then I use software
      driven soft limits while running to make sure I never actually hit
      the switch when the machine is moving.

      David Mikesell San Jose California

      Thanks David

      I'll  think about that so more.

      What is the limit switch voltage?


      Paul Lamar

      It's a 5vdc logic circuit.

      David Mikesell San Jose California


      I guess that is the reason some of the Kasuga docs I have recommended
      running the limit switch wires in separate conduit. Unfortunately it
      was NOT adhered to on this original installation. But I will fix that
      and run them in separate conduits.

      I am guessing but that would partially explain the dozens of
      capacitors used on all the high voltage wires.


      Thanks David

      Paul Lamar

      Paul,

      You should also used shielded two strand twisted wire for the limit
      switches. You can get false signals from other wires, encoders should
      also be shielded to prevent errors.


      David Mikesell San Jose California


    Personally, I wouldn't connect the limit switches to the E-Stop. It's
    hard on drives, plus if your homing the machine to the limit switches,
    you're stopping the drives when you do. Limit switches can be configured
    to motion stop, or pull power from the drives via software and are then
    not hammering the drives from the power side if the switch is hit.

      I'd also not recommend contactors (or SSR's) between the drive and
    motor, a good way to blow servo drives.

    I agree with shielded wiring, limit switches, encoder wiring and your
    spindle wiring if it's controlled via vfd.

    At least, when I built my mill it's how I did it. Ran very well, never
    blew a drive. I ran my wiring in a common cable carrier with ~25' of
    cable all running beside each other and no noise issues. I also star
    grounded my system, which I think helped with those potential issues also.

    Fwiw
    Jarrett Johnson

    I am not using contractors on the servo drives.

    On the spindle motor I am using a Speedcom 3 phase motor controller.
    I suspect the EMC software can turn that off depending on the logic.

    At least I think so. The limit switches probably feed into the EMC program
    and it decides  when to stop an axis drive or the spindle motor.

    Is that correct David?

    So far I have not found that in the EMC docs. Does not mean it is not there.
    As I learn these tidbits of info I have to read the EMC docs again
    and again so I learn more and more in the process.

    I am saving the contactors for the 3 phase  knee motor which will not
    be tied into the EMC software. It will be strictly controlled
    manually. I still need a schematic for that. Either that or a good
    book on 3 phase motor wiring.

    Jarrett, what software did you use for your NC mill?

    Paul Lamar

    The limit switches and the e-stop are all independent of each other in
    every installation I have done. Most people do them in a series because
    it is easier and takes less time and less input pins on the interface
    board. Problem is you never know which one is triggered.

    I give each one has is own 5vdc signal, and is normally wired NC so that
    a limit is hit, or switch failure, even if a connector or wire break it
    stops the mill. With each one wired independent you will get a flag
    indicating which system that trigger the event.

    I do not use contactors or SSR's between drives and motors. I was just
    telling Paul I do not use contactors for anything. I use SSRs for
    turning on coolant pumps, actuators for tool changers. This way you can
    use the standard 5vdc logic signal and the ssr triggers and lets what
    ever voltage ac or dc you are using to do its job. No transformers for
    worrying about voltage spikes to the control interface or line noise.

    Yes Paul, when we set up the multi-function board, there are numerous
    inputs just for signals. In EMC we will tell it what each pin is
    assigned to and whether it is in a pull up or pull down condition
    normally. That way any change from that state is registered and causes
    the action we want.

    It really is pretty easy, especially someone with your background. The
    real trick is learning when reading these manuals on controllers and
    software to realize what is really pertinent to your particular
    installation.

    When I come down and we do this, in the end you will feel like kicking
    yourself because it will go pretty fast and easy during the software
    setup. the hardest part is doing the motor tuning to set the speed,
    torque and revolutions per inch.

    David Mikesell
    San Jose, CA

    So shall I replace the knee contactors with solid state switches?
    Can I control them with that switch box?

    I love the idea of the 5 volt logic and doing away with all that
    dangerous 110 Volt switching.

    Do you have a schematic or do I need to program a Maximite to do it.

    I assume I need at least  two of these to reverse the motor?

    Still no need or intention to control it with EMC. I only need to set
    the knee height once per part type.


    Paul Lamar


    Well Paul, we can also set it up as another axis and you can come and
    from AMC War from within your G-Code running while running apart. Or we
    can use manual switches the way it's set up now.

    I need to see it and store a schematic of how it's set up now to decide
    the best way to run it

    David MikesellSan Jose California


    To make a schematic of what I have is really tough.

    Basically what it is doing is controlling the contactors by switching
    110 volt coils  on an off.

    Motor on motor off. Motor up motor down. That's it.

    Can I do it with just two 3 phase SS switches.

    Keep it simple. No need to get it into EMC.

    If you have a suggested schematic for the switching I can wire it up and
    test it
    before you get here.

    Are those 3 phase solid state switches OK?

    I think one big solid state switch could do all the 3 phase motor direction
    change and perhaps speed in one large  piece of silicon :-)


    Paul Lamar

Yes Paul you.can. The picture you sent, the cryodon, are the same ones I use. Never had a failure yet. Yes.they will.directly replace.the old contactor relays.

David Mikesell
San Jose California

I think this is a good way of doing it.
Four single throw SS switches.

To turn the motor off I think all I have to do is turn off the five volt
supply.  I'll use three big fuses in the 3 phase supply.

How many amps would you guess the knee motor to be?


Paul Lamar

    The Rotary Engine free News Letter. Powered by Linux. If you want off
    the list PLEASE let me know and I will remove  you.  ACRE NL web
    site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
    Copyright 1998-2017 All world wide rights reserved.