Subject: Allison PSRU no planet carrier. Reno racer.
From: paul lamar
Date: 4/1/2017, 7:20 PM
To: A10-Me-Earthlink


 The ring gear is exactly 7 inches in diameter. So a 8 inch OD tube
 with 1/2 inch wall is just right. A 7.5 might work if you shave some
 meat off the outside of the ring  gear.

 The bulk heads can be cut from aluminum plate on a band saw (or you
 can buy rounds) and trued up in the  lathe. Use a bunch of extended
 point set screws to center and lock the ring gear. The nose can be
 bar or tube. Best to just bolt the parts together with a bunch of
 1/4 inch bolts.

 One might get two housings out of one 12 inch long tube.

 BTW the ring gear alone weighs 4.2 pounds. Cutting it down to the
 width of the planet gears will get it down to roughly 3.6 pounds.

 the input shaft and sun gear are 6 pounds.

 The planet carrier, un machined, is 17 pounds. One may get it down
 to 10 pounds by machining it. It is very VERY expensive to cut it
 down so don't even think about it. Take the planets out and make a
 new planet carrier out of 6061 T6.

 ----------------------------------------------------------

 This is it. No separate planet carrier.

 The front and back flanges become the planet carrier further reducing
 the cost and weight. A custom aluminum planet cage would cost a lot
 in therms of NC machining time.

 The Allison comes with 3 planet gears but you can put in up to six.
 If you only use three the other three can be larger in diameter
 spacers up to one inch which will stiffen it up. I think three are
 enough as this is a real heavy duty transmission. Those planet gears
 are rather heavy.

 The bolts are ordinary  grade 8.... 7/16th bolts. The hollow planet
 shafts are about 5/8th OD and must be hardened and ground for the
 needle bearings in the planet gears.

 The correct size  shoulder bolts are hard to find. Also very
 expensive.

 I put in the Jerry Bass helical gear thrust bearing. It is the blue
 bearing in the 3D's.

 The planet shafts are recessed into the front and back flanges for
 accuracy and torsional stiffness.

 Paul Lamar

 Planet rebuild kits are readily available from Allison.  I would
 think Ti or Gama TiAl would be the way to go for the planet carrier.
 Better fatigue resistance and lighter than the steel. There is one
 transmission that has a 3.5:1 low gear without being compound. I
 think it is a MT640.

 Dale Davies

 This one is 3.1 to one according Aubrey.

 Here it is put together. Very compact. Good for 1300 HP Reno 4 rotor.
 I  suspect it will be around 30 pounds. 5 pounds less than the Bell
 47 with out the Sonja :-)

 Paul Lamar



 Hi Paul, the 2 photo's of transmission parts in this attachment, are
 from what transmission?

 Thanks, Steve Carlisle

 In Trans1.jpg it is the Ford on the left and the Allison on the
 right. Trans2.jpg is all Allison. Very very heavy.  You won't need
 this till you get over 500 HP.

 Paul Lamar



 Paul, thanks for the info, my idea is if you are going to put the
 effort into building a PSRU, you may as well make it handle 500HP!
 Likely no more effort, and not much more wieght.

 Steve Carlisle

 A lot more weight. Everything is bigger and heavier from the input shaft to the
sun gear to the planet carrier to the ring gear to the prop shaft to the
prop flange.Not to mention the box itself.

I would not be a bit surprised if you wound up with 75 pounds.
Exactly in the wrong position for CG reasons.

Are you building a turbo 3 or 4 rotor for a DH Beaver radial 985 replacement engine ? :-)

I know of few experimental airplanes that need that amount of power.

Perhaps the Ledgen PT6 turbo prop.

How about a Ledgen on floats?  :-)

Paul Lamar


 The Rotary Engine free News Letter. Powered by Linux. If you want off
 the list PLEASE let me know and I will remove  you.  ACRE NL web
 site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
 Copyright 1998-2016 All world wide rights reserved.