Subject: Allison PSRU no planet carrier. Reno racer.
From: paul lamar
Date: 4/2/2017, 10:05 AM
To: A10-Me-Earthlink



The ring gear is exactly 7 inches in diameter. So a 8 inch OD tube
with 1/2 inch wall is just right. A 7.5 might work if you shave some
meat off the outside of the ring  gear.

The bulk heads can be cut from aluminum plate on a band saw (or you
can buy rounds) and trued up in the  lathe. Use a bunch of extended
point set screws to center and lock the ring gear. The nose can be
bar or tube. Best to just bolt the parts together with a bunch of 1/4
inch bolts.

One might get two housings out of one 12 inch long tube.

BTW the ring gear alone weighs 4.2 pounds. Cutting it down to the
width of the planet gears will get it down to roughly 3.6 pounds.

the input shaft and sun gear are 6 pounds.

The planet carrier, un machined, is 17 pounds. One may get it down to
10 pounds by machining it. It is very VERY expensive to cut it down
so don't even think about it. Take the planets out and make a new
planet carrier out of 6061 T6.

----------------------------------------------------------

This is it. No separate planet carrier.

The front and back flanges become the planet carrier further
reducing the cost and weight. A custom aluminum planet cage would
cost a lot in therms of NC machining time.

The Allison comes with 3 planet gears but you can put in up to six.
If you only use three the other three can be larger in diameter
spacers up to one inch which will stiffen it up. I think three are
enough as this is a real heavy duty transmission. Those planet gears
are rather heavy.

The bolts are ordinary  grade 8.... 7/16th bolts. The hollow planet
shafts are about 5/8th OD and must be hardened and ground for the
needle bearings in the planet gears.

The correct size  shoulder bolts are hard to find. Also very
expensive.

I put in the Jerry Bass helical gear thrust bearing. It is the blue
bearing in the 3D's.

The planet shafts are recessed into the front and back flanges for
accuracy and torsional stiffness.

Paul Lamar

Planet rebuild kits are readily available from Allison.  I would
think Ti or Gama TiAl would be the way to go for the planet carrier.
Better fatigue resistance and lighter than the steel. There is one
transmission that has a 3.5:1 low gear without being compound. I
think it is a MT640.

Dale Davies

This one is 3.1 to one according Aubrey.

Here it is put together. Very compact. Good for 1300 HP Reno 4
rotor. I  suspect it will be around 30 pounds. 5 pounds less than the
Bell 47 with out the Sonja :-)

Paul Lamar



Hi Paul, the 2 photo's of transmission parts in this attachment, are
from what transmission?

Thanks, Steve Carlisle

In Trans1.jpg it is the Ford on the left and the Allison on the
right. Trans2.jpg is all Allison. Very very heavy.  You won't need
this till you get over 500 HP.

Paul Lamar



Paul, thanks for the info, my idea is if you are going to put the
effort into building a PSRU, you may as well make it handle 500HP!
Likely no more effort, and not much more wieght.

Steve Carlisle

A lot more weight. Everything is bigger and heavier from the input
shaft to the sun gear to the planet carrier to the ring gear to the
prop shaft to the prop flange.Not to mention the box itself.

I would not be a bit surprised if you wound up with 75 pounds.
Exactly in the wrong position for CG reasons.

Are you building a turbo 3 or 4 rotor for a DH Beaver radial 985
replacement engine ? :-)

I know of few experimental airplanes that need that amount of power.

Perhaps the Ledgen PT6 turbo prop.

How about a Ledgen on floats?  :-)


Paul Lamar

Hi Paul, I was just going through related e-mails on PSRU parts
donors, to get a idea on what was the most current transmission
candidate. It seems the Ford E4OD  P1 would be the choice. But what
is the ratio of that planetary ? Also the Allison 1000 /GMC trucks,
3.10 to 1 would be a choice.

Steve Carlisle

I stuck the Allison in my lathe and it is near impossible to cut it
down. Apparently the whole planet carrier is hardened.  In the remote
chance I needed it I would remove the planets and needle bearings
and make a new carrier out of aluminum. It weighs 16.7 pounds stock.

The Ford weighs 3.5 pounds with a steel planet carrier.

IMHO the Ford will work for everything up to 500 HP. The ratio with
the ring gear held is something like 3.12 to one.


Paul Lamar



Thanks Paul, it should not be too hard to find the ford parts.

Steve Carlisle

The Rotary Engine free News Letter. Powered by Linux. If you want
off the list PLEASE let me know and I will remove  you.  ACRE NL web
site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
Copyright 1998-2016 All world wide rights reserved.