I am also working on the design of the end housings. The rear is
quite simple.
The front end housing must accommodate a water pump. Does anybody
have any preferences for water pumps. 2nd gen or RX8? Or some else
perhaps?
The oil pump with be a dry sump pump with choices of several brands.
Pual Lamar
In regard to your water pump choice question I would like to comment.
If designing a different front cover, the water pump chosen firstly
needs to meet the flow requirements of the engine. The pulley needs
to match with regard to belt type and width as well as diameter. Then
replacement cost and availability need consideration. Accessibility
at any location in firstly N. America and potentially the world
should be taken into consideration. Possibly the pump from a Cummins
diesel as installed in Dodge or Ram trucks would work.
Dale Davies
Paul I like the 2nd generation RX8 pump. From left to right: 2nd gen
RX8, 1st gen RX8 and Remedy RX8 (See attached).
Barry Bordes
Maybe I'm just blowing smoke here.. Suppose turbo extracted power
from the exhaust to drive a water pump that is redundant to a pump
on the eccentric shaft. Plumbd together, excess power in the exhaust
might compound to the engine through the pump?
Lewis. Bjork
I'd like to see all accessories driven from the eccentric shaft or
gear box. Built in water pump on the housing, perhaps an alternator
in the gru. This would keep frontal area remarkably small.
Lewis Bjork.
Hi Paul,
Would an electric water pump be applicable in this case? You could
modulate the cooling rate from a sensor reading water temperature.
It could be mounted anywhere.
Cheers,
Russ Ward
If some one could come up with an electric water pump capable of
pumping 3 Horse Power worth of water that would be great. That's
what it takes to cool a constant 200 HP internal combustion engine.
3 HP is 2,238 watts. 746 watts is one HP. Add 20% for inefficiency
and you have 2,865 watts.
At a battery voltage of 12 Volts THE current out of the battery or
alternator required is 223 AMPS!!!!!
Horse Power in watts is voltage times current.
Paul Lamar
Why not just put an inlet and outlet for coolant and multiple bosses
to attach the coolant pump and other accessories. Many coolant pumps
are all one piece and do not need a back plate. Sure would make the
machining of the front housing easier.
chris smale
I would like to have seen the fabrication of these steel end housings
on the SuperLite rotary. Lots of work and skill !
Steve Carlisle
Where did you get the idea they were steel. I don't recall that.
Paul Lamar
IDEA, okay, first is the 2 weld joints at the top of the housing,
second is the thermal coolant marking on the housing end face, and
the third is the rust on the sharp edges of the housing, which also
seems to match the rust on the end of the housing bolts. metal color
is also quite different than cast iron and aluminum. Also in your
correspondence somewhere is a mention of steel fabricated housings.
And also in attached picture, of a silver soldered joint in the
center housing. I base this judgement of 40 years related fabrication
and mechanical experience.
Steve Carlisle
Paul Lamar
Here are some more pictures and a PDF article by Steve Beckham
Paul Lamar
Hi Paul, thanks for the info. You provided all those pics to me many
moons ago, but not the PDF, provides a little more historical info. I
wish there was a PDF from Everett Hatch on the historical development
of his engines.
Steve Carlisle
Unfortunately Everett is no longer with us.
Steve sent me a movie some time ago but it was too large to publish.
I recently acquired a way to lower the rez and the file size so
here it is.
Fortunately the process does not change the sound.
Paul Lamar
I bet that pissed the neighbors off !
Steve Carlisle
The Rotary Engine free News Letter. Powered by Linux. If you want
off the list PLEASE let me know and I will remove you. ACRE NL web
site.
http://www.rotaryeng.net You Tube
http://tinyurl.com/beqqxas
Copyright 1998-2017 All world wide rights reserved.