Subject: design of the end housings
From: paul lamar
Date: 4/13/2017, 6:05 PM
To: A10-Me-Earthlink




 I am also working on the design of the end housings. The rear is
 quite simple.

 The front end housing must accommodate a water pump. Does anybody
 have any preferences for water pumps. 2nd gen or RX8? Or some else
 perhaps?

 The oil pump with be a dry sump pump with choices of several brands.


 Pual Lamar


 In regard to your waterpump choice question I would like to comment.
 If designing a different front cover, the water pump chosen firstly
 needs to meet the flow requirements of the engine. The pulley needs
 to match with regard to belt type and width as well as diameter. Then
 replacement cost and availabiliry need consideration. Accessability
 at any location in firstly N. America and potentially the world
 should be taken into consideration. Possibly the pump from a Cummins
 diesel as installed in Dodge or Ram trucks would work. Dale Davies


 I think it matters to which type of end housing design you have
 chosen !

 Steve Carlisle

 <Rotaryview.jpg


 Can someone please clue me in on the engine on the right in this
 photo from back on April 9?  Is there a write-up on this engine
 somewhere?  I tried to blow it up and read the placard on the bottom,
 but the photo resolution is too low.

 Dave Klingler

 It is an old Power Sport light weight engine. Did you miss that
 thread?

 Here is some more stuff  on the Old Power Sport.

 Paul Lamar


I can't get past this idea. Ceramics are haunting me. I know that a
coating could come off. For much greater combustion heat what if we do a
ceramic housing or better yet a ceramic housing and rotors as well?
Using a high heat alloy for the combustion chamber on the ceramic
rotor.  They have run all ceramic piston v6 motors with no cooling system.
I went to search for the V6 for reference and I found this! Good things
are coming as necessity is the Mother of invention.
http://ceramicrotaryengines.com <http://ceramicrotaryengines.com/>

Diesel fuel with its 20% higher energy content per equal mass to
Gasoline could go a lot further with a given amount of fuel. I was
thinking E-Charger for starting but stratified charge converting to
compression ignition once the Turbos spooled up would be perfect. Small
ceramic rotary ultralight motor?
https://youtu.be/YnfFEf7wyww
Here is the V6 I was thinking about.
https://youtu.be/sAk5tc_gpmo

GE is making huge strides in Ceramics
https://youtu.be/is1BBilkyUM
I'm more convinced than ever now.

Kurt Emerson

The idea of ceramic rotors has been around for years. As I recall a
British company made and tested a ceramic rotor. I searched my files but
I could not find it.
Apparently the results were disappointing. If it had worked it would
have been available by now.


The total cooling losses are only 25% of all the losses.
The exhaust is about 50%. So turbo compound has the best chance of
making a big difference. I think the company that did that ceramic
rotors are gone.

I have no doubt they would be strong enough as silicon nitride apex
seals are wonderful. The F1 guys use all ceramic ball bearings as does
the turbo charger in the TTC.

SAE  860616 paper is on the subject but I am not going to buy it.
If some one has it perhaps they can scan it for us.

Paul Lamar



Kurt,
   Thank you for your missive on ceramics, I also curse you for it as
I stayed up ALL NIGHT following the links, it fair did my head in to be
sure but what an eye opener ! it is only when one
reads knowledge like this that one realizes what little one actually
knows, I salute you. It reminds me of when Paul stayed here, the man
NEVER SLEPT ! until I joined this news letter I thought that
   rotaries just went round and round instead of up and down, how
wrong I was !

Chris Hoskins

Kurt,
I agree that ceramics sound good. But I am also aware that the so-called 'Adiabatic' reciprocating piston engine was disappointing regarding higher efficiency. All that was happening was that the total temperature profile was raised but delta T was about the same. Efficiency = (T-in - T-out) / T-in. The difference between T-in and T-out is important.

It would be nice to know if the 'Ceramic Engine' people would have any real measurements. It is now a few years back since they had that 5 cc engine running in ceramics. No results have been made public, at least I am not aware of it. Maybe they have the same experience as the results with the RPE experiments? Sure, they do not need a cooling system. The temperature instead goes out the exhaust that is hotter by about the same amount. The all important difference is key and it does not seem to improve with reducing the heat flow to the cooling system. T-in goes up and so does T-out. T-in is the max temperature at combustion near TDC and T-out is the exhaust gas temperature or at BDC.

Since we have not heard more news form 'Ceramic Engines' it may be save to conclude that the results were the same as those obtained from the RPE. A higher compression ratio or rather expansion ratio provides a higher delta T.  The Turbine engine benefits form higher initial temperature that the blades can take as the delta T is being increased as far as I am aware.

Rolf Pfeiffer



The Rotary Engine free News Letter. Powered by Linux. If you want off
the list PLEASE let me know and I will remove  you.  ACRE NL web
site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
Copyright 1998-2017 All world wide rights reserved.