Subject: How many people are building airplanes?
From: paul lamar
Date: 5/30/2017, 2:07 AM
To: A10-Me-Earthlink


Hello Le Roux,
I believe my Bede BD4 was originally built in South Africa and imported into the UK. It is a very well built and maintained example. The wings are just superb.  I bought it after it was advertised for sale as parts and I put a proposal forward for the whole airframe less engine and instruments.

I first read of these aircraft in the late 60's or early 70's and never ever thought I would be able to own one. This aircraft was acquired by a new owner last year after being advertised in excess of £22,000. The new owner experienced the loss of power just after takeoff and put it down in a field causing damage to firewall, lower engine mounts, nose leg, and cockpit floor.

Not surprising as after the nose leg collapsed that airframe would have been doing a good job of trying to plough up the field with that sharp vertical bottom edge of the firewall.

Perhaps builders should put more thought into what is the likely chain of events once an aircraft has touched down in an off field emergency landing. I think the damage sustained could have been greatly reduced if there was a upward curved section of alloy sheet across the bottom of the firewall. Just as Paul has suggested for the exit of cooling air but perhaps with extra strength for exceptional circumstances. At least then the front of fuselage couldn't dig in after the collapse of the undercarriage and bottom engine cover.

Anyway , Paul has just written in another email about buying airframes and I wanted to say that I got this little beauty after the accident for £600.  This means I might be able to rebuild for a very sensible sum (and a lot of labour)

The great thing about the BD4 is that the skin is non structural and the frame is just bolted together. All I have to do is remove enough skin and unbolt enough parts to take me back to an unaffected area of the frame and  then start building back out bending up new sections of frame using the original bits as patterns. I have built a steel jig so that the fuselage is hanging from the centre spar leaving me free to work front lower fuselage unhindered.

Lastly because of the low initial investment if at any time I find the airframe an unrepairable total loss or the British authorities say no, what the heck. I am loving every minute of it , learning so much daily and acquiring the tools and skills I need to build . Also ,as I work I have the remainder of the aircraft and wings to look at and dream.

Paul, thank you for those other photos. Good guide there for the engine mount.

Regards
Mark Dillner


  How many people are building airplanes?

  Paul Lamar

  Hello Paul, I am slowly working on the rebuild of  Zenair CH250 and
  Bede BD4. Both were damaged in landing accidents. I bought the
  airframes without engines or instruments. G-RAYS is the Zenair.
  Everything is a learning curve for me.

  I have put both these aircraft in steel jigs .Just coming to grips
  with the best way to remove the pop rivets in the areas requiring
  repair is of interest to me right now. Some rivets seem much tougher
  than others like there is a variation in the type used especially in
  the BD4. I have been punching out the steel centre shaft first . Some
  don't want to budge and there is only so much force I can use. I have
  then drilled in with a 1/8 drill bit but some seem to slip from the
  centre especially when the core steel is still in it. This can easily
  lead to damage to the surrounding area which is fine when I can't
  reuse the skin anyway but I would like to be bang on so I don't cause
  damage when I come to peel open the wing skins for a good inspection
  inside on the Zenair . Once I have drilled in just below skin surface
  depth or sometimes all the way through I knock the top of the rivet
  off with a small chisel.


  Any hints or advice would be appreciated.


  Although I have collected a number of different automotive engines
  including the Subaru, Rover V8 and Corvair my gut feeling is the
  Mazda RX8 (of which I have got three) gives me the best solution. The
  Mazda has the best ability to produce a high power to weight ratio.
  However the Zenair at least has a recommended max firewall forward
  weight of 300lbs and I would really like to be well under this . It's
  for this reason I am looking at ways to reduce the Mazda basic weight
  and find your discussion of alloy end plates most interesting. I am
  waiting on a chance to get together with a friend who is going to
  machine down a couple of end plates to see what I have to play with .
  I am thinking along the lines of milling the end plates down to about
  half an inch thick then making up a water jacket a bit like the oil
  sump.


  Water pump from a v6 ford is a self contained item so that can be run
  by belt and I am looking for a dry sump oil pump.


  You were also talking at one time of electric points being run on
  the crank shaft. What I don't yet know is how many times the points
  on the Mazda need to fire per revolution of the crank. Could you help
  me on that one?


  One other question I have is regarding superchargers or turbo
  chargers. Sometimes I read how an automotive turbo charger is not
  ideal in an aircraft as it runs at a high capacity for long periods.
  Is this truly a problem and if so what sort of turbocharger should I
  be looking for?

  My work away from home as a live in carer (although it is only 15
  weeks or so a year)  and the fact that I have to go from England to
  France as often as possible to maintain my home there means work on
  my planes is sporadic . I wish I had started on pursuing my true
  interest many,many years ago and I have a lot of catching up to do.


  I would like to take this opportunity to once again thank you for
  allowing me access to your vast knowledge and experience by way of
  the internet. Regards Mark Dillner UK

  Thanks Mark.

  Q1 "You were also talking at one time of electric points being run
  on the crank shaft."

  Each Wankel rotor fires once per revolution of the e-shaft so a very
  simple inductive ignition is all you need.  In aircraft use there is
  no real need for ignition advance. Set the advance to 22 degrees
  BTDC.

  One set of points for each rotor. One cam for each rotor. The points
  are closed for 90% of the time. When the points open the coil fires
  the plug. Since the Mazda has two plugs per rotor wire two coils in
  parallel.

  Now you need a second set of everything for the second rotor. Mount
  the second cam 180 degrees away from the first cam.

  That is all there is to it. A super simple ignition system two rotor
  ignition system. Highly reliable. Check the wear on the points from
  time to time and replace as necessary.

  RX8 coils and a lot of others these days have solid state switches
  built in so the points no longer carry a lot of current.


  Q2 "automotive turbo charger is not ideal in an aircraft"

  That is true.  Use as large a turbo as you can get  and use a blow
  off valve on the intake manifold set to what ever boost or HP you
  want.

  The reason for this is you don't need rapid spool up for the turbo
  charger and a large turbine is more durable at the 1800 F exhaust
  temperatures involved.

  You can use a by pass hole in the exhaust manifold venting the
  exhaust system to the atmosphere.

  No real need for a waste gate. About a inch and a quarter hole is
  about right. Make it larger for less boost.  I would say at this
  point 80 inches of Mercury will give you about  650 HP at 8000 RPM in
  a two rotor with a very effective intercooler. You control this with
  the blow off valve,

  Keep the manifold air temperature below 150 degrees Fahrenheit. You
  might need water injection for take off power if your intercooler
  does not do the job..

  More like 40 or 45 inches of mercury is about right for most
  experimental aircraft. You will get something like 300 or 350 HP max
  take off power.


  With Iannetti silicon nitride apex seals the life of the Mazda rotary
  is unlimited in aircraft use.


  Paul Lamar


  Thanks Paul

  Mark Dillner

  Hi Mark included a photo of the first completed BD4C aircraft in the
  world. I helped a friend Marcel Viljoen, the ownerbuilder on the
  project.We finnished the BD in 2011
A remarkable aircraft and design by Jim Bede.As you will see
  the fuselage is a airfoil itself and contribute to lift.Very clever

We flew this past weekend in the Presidents Trophy Airrace in South
Africa and again the plane amazed me.Maybe not so soft on the eyes but
very efficient and fast.If you put the nose down slightly it pick up
speed immediately. It has a lycoming IO390 and 3 blade Catoprop

Le Roux Breytenbach

People have put rotaries in them and flown them. Here are some pictures.
The cooling system on this one is not the best.

Paul Lamar

Hello Le Roux,
I believe my Bede BD4 was originally built in South Africa and imported into the UK. It is a very well built and maintained example. The wings are just superb.  I bought it after it was advertised for sale as parts and I put a proposal forward for the whole airframe less engine and instruments.

I first read of these aircraft in the late 60's or early 70's and never ever thought I would be able to own one. This aircraft was acquired by a new owner last year after being advertised in excess of £22,000. The new owner experienced the loss of power just after takeoff and put it down in a field causing damage to firewall, lower engine mounts, nose leg, and cockpit floor.

Not surprising as after the nose leg collapsed that airframe would have been doing a good job of trying to plough up the field with that sharp vertical bottom edge of the firewall.

Perhaps builders should put more thought into what is the likely chain of events once an aircraft has touched down in an off field emergency landing. I think the damage sustained could have been greatly reduced if there was a upward curved section of alloy sheet across the bottom of the firewall. Just as Paul has suggested for the exit of cooling air but perhaps with extra strength for exceptional circumstances. At least then the front of fuselage couldn't dig in after the collapse of the undercarriage and bottom engine cover.

Anyway , Paul has just written in another email about buying airframes and I wanted to say that I got this little beauty after the accident for £600.  This means I might be able to rebuild for a very sensible sum (and a lot of labour)

The great thing about the BD4 is that the skin is non structural and the frame is just bolted together. All I have to do is remove enough skin and unbolt enough parts to take me back to an unaffected area of the frame and  then start building back out bending up new sections of frame using the original bits as patterns. I have built a steel jig so that the fuselage is hanging from the centre spar leaving me free to work front lower fuselage unhindered.

Lastly because of the low initial investment if at any time I find the airframe an unrepairable total loss or the British authorities say no, what the heck. I am loving every minute of it , learning so much daily and acquiring the tools and skills I need to build . Also ,as I work I have the remainder of the aircraft and wings to look at and dream.

Paul, thank you for those other photos. Good guide there for the engine mount.

Regards
Mark Dillner UK

Our new universal mount is easer to fabricate.Based on what Bristol did in WW II.
http://www.rotaryeng.net/motor.html

That  BD5 airplane was also wrecked in a botched landing. I don't know what happened
to the remains. The fuse was wrinkled a bit and one wing tip damaged. Then the
builder much later died of natural causes. Old age or a heart attack I think. That was about
five or ten years ago. I have a complete set of plans for a BD5 in a large book form.

Paul Lamar


The Rotary Engine free News Letter. Powered by Linux. If you want off
the list PLEASE let me know and I will remove  you.  ACRE NL web
site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
Copyright 1998-2017 All world wide rights reserved.