Subject: How many people are building airplanes?
From: paul lamar
Date: 5/30/2017, 1:55 PM
To: A10-Me-Earthlink


Le Roux
 Hello Le Roux, I believe my Bede BD4 was originally built in South
 Africa and imported into the UK. It is a very well built and
 maintained example. The wings are just superb.  I bought it after it
 was advertised for sale as parts and I put a proposal forward for
 the whole airframe less engine and instruments.

 I first read of these aircraft in the late 60's or early 70's and
 never ever thought I would be able to own one. This aircraft was
 acquired by a new owner last year after being advertised in excess
 of £22,000. The new owner experienced the loss of power just after
 takeoff and put it down in a field causing damage to firewall, lower
 engine mounts, nose leg, and cockpit floor.

 Not surprising as after the nose leg collapsed that airframe would
 have been doing a good job of trying to plough up the field with
 that sharp vertical bottom edge of the firewall.

 Perhaps builders should put more thought into what is the likely
 chain of events once an aircraft has touched down in an off field
 emergency landing. I think the damage sustained could have been
 greatly reduced if there was a upward curved section of alloy sheet
 across the bottom of the firewall. Just as Paul has suggested for
 the exit of cooling air but perhaps with extra strength for
 exceptional circumstances. At least then the front of fuselage
 couldn't dig in after the collapse of the undercarriage and bottom
 engine cover.

 Anyway , Paul has just written in another email about buying
 airframes and I wanted to say that I got this little beauty after
 the accident for £600.  This means I might be able to rebuild for a
 very sensible sum (and a lot of labour)

 The great thing about the BD4 is that the skin is non structural and
 the frame is just bolted together. All I have to do is remove enough
 skin and unbolt enough parts to take me back to an unaffected area
 of the frame and  then start building back out bending up new
 sections of frame using the original bits as patterns. I have built a
 steel jig so that the fuselage is hanging from the centre spar
 leaving me free to work front lower fuselage unhindered.

 Lastly because of the low initial investment if at any time I find
 the airframe an unrepairable total loss or the British authorities
 say no, what the heck. I am loving every minute of it , learning so
 much daily and acquiring the tools and skills I need to build . Also
 ,as I work I have the remainder of the aircraft and wings to look at
 and dream.

 Paul, thank you for those other photos. Good guide there for the
 engine mount.

 Regards Mark Dillner


 How many people are building airplanes?

 Paul Lamar

 Hello Paul, I am slowly working on the rebuild of  Zenair CH250 and
 Bede BD4. Both were damaged in landing accidents. I bought the
 airframes without engines or instruments. G-RAYS is the Zenair.
 Everything is a learning curve for me.

 I have put both these aircraft in steel jigs .Just coming to grips
 with the best way to remove the pop rivets in the areas requiring
 repair is of interest to me right now. Some rivets seem much tougher
  than others like there is a variation in the type used especially in
  the BD4. I have been punching out the steel centre shaft first .
 Some don't want to budge and there is only so much force I can use.
 I have then drilled in with a 1/8 drill bit but some seem to slip
 from the centre especially when the core steel is still in it. This
 can easily lead to damage to the surrounding area which is fine when
 I can't reuse the skin anyway but I would like to be bang on so I
 don't cause damage when I come to peel open the wing skins for a
 good inspection inside on the Zenair . Once I have drilled in just
 below skin surface depth or sometimes all the way through I knock the
 top of the rivet off with a small chisel.


 Any hints or advice would be appreciated.


 Although I have collected a number of different automotive engines
 including the Subaru, Rover V8 and Corvair my gut feeling is the
 Mazda RX8 (of which I have got three) gives me the best solution. The
 Mazda has the best ability to produce a high power to weight ratio.
 However the Zenair at least has a recommended max firewall forward
 weight of 300lbs and I would really like to be well under this . It's
 for this reason I am looking at ways to reduce the Mazda basic weight
 and find your discussion of alloy end plates most interesting. I am
 waiting on a chance to get together with a friend who is going to
 machine down a couple of end plates to see what I have to play with .
 I am thinking along the lines of milling the end plates down to about
 half an inch thick then making up a water jacket a bit like the oil
 sump.


 Water pump from a v6 ford is a self contained item so that can be run
 by belt and I am looking for a dry sump oil pump.


 You were also talking at one time of electric points being run on
 the crank shaft. What I don't yet know is how many times the points
 on the Mazda need to fire per revolution of the crank. Could you help
 me on that one?


 One other question I have is regarding superchargers or turbo
 chargers. Sometimes I read how an automotive turbo charger is not
 ideal in an aircraft as it runs at a high capacity for long periods.
  Is this truly a problem and if so what sort of turbocharger should I
  be looking for?

 My work away from home as a live in carer (although it is only 15
 weeks or so a year)  and the fact that I have to go from England to
 France as often as possible to maintain my home there means work on
 my planes is sporadic . I wish I had started on pursuing my true
 interest many,many years ago and I have a lot of catching up to do.


 I would like to take this opportunity to once again thank you for
 allowing me access to your vast knowledge and experience by way of
 the internet. Regards Mark Dillner UK

 Thanks Mark.

 Q1 "You were also talking at one time of electric points being run
 on the crank shaft."

 Each Wankel rotor fires once per revolution of the e-shaft so a very
  simple inductive ignition is all you need.  In aircraft use there is
  no real need for ignition advance. Set the advance to 22 degrees
 BTDC.

 One set of points for each rotor. One cam for each rotor. The points
  are closed for 90% of the time. When the points open the coil fires
  the plug. Since the Mazda has two plugs per rotor wire two coils in
  parallel.

 Now you need a second set of everything for the second rotor. Mount
 the second cam 180 degrees away from the first cam.

 That is all there is to it. A super simple ignition system two rotor
  ignition system. Highly reliable. Check the wear on the points from
  time to time and replace as necessary.

 RX8 coils and a lot of others these days have solid state switches
 built in so the points no longer carry a lot of current.


 Q2 "automotive turbo charger is not ideal in an aircraft"

 That is true.  Use as large a turbo as you can get  and use a blow
 off valve on the intake manifold set to what ever boost or HP you
 want.

 The reason for this is you don't need rapid spool up for the turbo
 charger and a large turbine is more durable at the 1800 F exhaust
 temperatures involved.

 You can use a by pass hole in the exhaust manifold venting the
 exhaust system to the atmosphere.

 No real need for a waste gate. About a inch and a quarter hole is
 about right. Make it larger for less boost.  I would say at this
 point 80 inches of Mercury will give you about  650 HP at 8000 RPM in
 a two rotor with a very effective intercooler. You control this with
 the blow off valve,

 Keep the manifold air temperature below 150 degrees Fahrenheit. You
 might need water injection for take off power if your intercooler
 does not do the job..

 More like 40 or 45 inches of mercury is about right for most
 experimental aircraft. You will get something like 300 or 350 HP max
  take off power.


 With Iannetti silicon nitride apex seals the life of the Mazda rotary
 is unlimited in aircraft use.


 Paul Lamar


 Thanks Paul

 Mark Dillner

 Hi Mark included a photo of the first completed BD4C aircraft in the
  world. I helped a friend Marcel Viljoen, the ownerbuilder on the
 project.We finnished the BD in 2011 A remarkable aircraft and design
 by Jim Bede.As you will see the fuselage is a airfoil itself and
 contribute to lift.Very clever

 We flew this past weekend in the Presidents Trophy Airrace in South
 Africa and again the plane amazed me.Maybe not so soft on the eyes
 but very efficient and fast.If you put the nose down slightly it
 pick up speed immediately. It has a lycoming IO390 and 3 blade
 Catoprop

 Le Roux Breytenbach

 People have put rotaries in them and flown them. Here are some
 pictures. The cooling system on this one is not the best.

 Paul Lamar

 Hello Le Roux, I believe my Bede BD4 was originally built in South
 Africa and imported into the UK. It is a very well built and
 maintained example. The wings are just superb.  I bought it after it
 was advertised for sale as parts and I put a proposal forward for
 the whole airframe less engine and instruments.

 I first read of these aircraft in the late 60's or early 70's and
 never ever thought I would be able to own one. This aircraft was
 acquired by a new owner last year after being advertised in excess
 of £22,000. The new owner experienced the loss of power just after
 takeoff and put it down in a field causing damage to firewall, lower
 engine mounts, nose leg, and cockpit floor.

 Not surprising as after the nose leg collapsed that airframe would
 have been doing a good job of trying to plough up the field with
 that sharp vertical bottom edge of the firewall.

 Perhaps builders should put more thought into what is the likely
 chain of events once an aircraft has touched down in an off field
 emergency landing. I think the damage sustained could have been
 greatly reduced if there was a upward curved section of alloy sheet
 across the bottom of the firewall. Just as Paul has suggested for
 the exit of cooling air but perhaps with extra strength for
 exceptional circumstances. At least then the front of fuselage
 couldn't dig in after the collapse of the undercarriage and bottom
 engine cover.

 Anyway , Paul has just written in another email about buying
 airframes and I wanted to say that I got this little beauty after
 the accident for £600.  This means I might be able to rebuild for a
 very sensible sum (and a lot of labour)

 The great thing about the BD4 is that the skin is non structural and
 the frame is just bolted together. All I have to do is remove enough
 skin and unbolt enough parts to take me back to an unaffected area
 of the frame and  then start building back out bending up new
 sections of frame using the original bits as patterns. I have built a
 steel jig so that the fuselage is hanging from the centre spar
 leaving me free to work front lower fuselage unhindered.

 Lastly because of the low initial investment if at any time I find
 the airframe an unrepairable total loss or the British authorities
 say no, what the heck. I am loving every minute of it , learning so
 much daily and acquiring the tools and skills I need to build . Also
 ,as I work I have the remainder of the aircraft and wings to look at
 and dream.

 Paul, thank you for those other photos. Good guide there for the
 engine mount.

 Regards Mark Dillner UK

 Our new universal mount is easer to fabricate.Based on what Bristol
 did in WW II. http://www.rotaryeng.net/motor.html

 That  BD5 airplane was also wrecked in a botched landing. I don't
 know what happened to the remains. The fuse was wrinkled a bit and
 one wing tip damaged. Then the builder much later died of natural
 causes. Old age or a heart attack I think. That was about five or
 ten years ago. I have a complete set of plans for a BD5 in a large
 book form.

 Paul Lamar

 The engine cowl which Bedecorp now sells for the BD 4 is the one in
 the picture i have send.

We have build the male plug for the glass fiber cowl and Bede corp took it over from Marcel Viljoen
The inlets as said is for Lycoming engines but can be used for Pauls side mounted heat exchanger.
ZU-MBD was handicapped for 160,8 knots in the air race this year after we won the race in 2013 on a 159 knot handicap.

On strait and level the BD 4 easily reaches 160 - 170 knots on low altitude 3000 f
With 250 Hp it will climb like a "homesick angel"
Thanks Paul for letting us a talk about the stuff we love so much.

Le Roux Breytenbach

A brilliant design of a real easy to build aircraft. Typical of Jim Bede.

There is lots of room in the cowl for a good cooling system.
Here are some 3D's and dims. Old style welded motor mount.

Paul Lamar

 The Rotary Engine free News Letter. Powered by Linux. If you want off
 the list PLEASE let me know and I will remove  you.  ACRE NL web
 site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
 Copyright 1998-2017 All world wide rights reserved.