Subject: Warp drive hub non NC mill version
From: paul lamar
Date: 6/13/2017, 8:06 PM
To: A10-Me-Earthlink



    Most people that have NC Mill's need to pay for them. That increases
    the cost of the parts.

    Here is a version of the warp drive hub/prop-flange/combination. It
    weighs more but it can be built with just any old  lathe.

    Twelve 3/8" set point screws anchor it to the hollow prop shaft.

    Anybody have a big lathe that can turn 9 inch diameter? I can send
    you the round blanks. It would be nice if you had Rhino or Solid
    Works but not essential.

    I need a set front and back for the gear box prototype.

    BTW the best blade I have seen so far is the Sensenich. The secret
    to more HP is a wider blade.


    Paul Lamar


    I have a 16" lathe, but how would you guarantee 120 degree placement
    of the blade mounts? Even the slightest offset would cause
    significant vibration.

    That being said, if I turned it down a local shop here has an NC mill
    that could drill the blanks. Their costs are reasonable, $70 an
    hour.


    Kevin Alderman

    That is a good hourly rate for an NC shop. If you give me the name I
    will request some quotes.

    I have a rotary table.

    Here is a company that keeps a low profile but they have great prices
    on machine tools. http://www.shars.com/ down load the pdf catalog.

    In case you need a rotary table.


    Paul Lamar

    Kevin, you can clamp a degree wheel to the rear of the spindle, and
    index from there!

    Steve carlisle


    Steve, I know about the degree wheel, but the bolt holes aren't my
    concern. It's the prob blade holes. Just 1 degree off or not
    perfectly bored and I get to spend a day trying to balance it.

    Making it round and bolting it together is the easy part. I figured I
    could turn out the blanks and the local shop do the bores.

    Kevin Alderman

    Check with Sensenich on the shank dimensions and see if they are the
    same as the warp drive.

    You will have to static balance it in any case. You will need to make
    a short shaft to do this and two parallel bars to do it on. Static
    balance is sufficient as blade deflection out of plane will happen no
    matter what. The quality control on the blade is most important for
    dynamic balance.

    Paul Lamar


    Kevin, is not the 120 degrees the same on the face as the periphery
    ?

    Steve Carlisle


   Yes, but to make this part you have to machine both pieces and then bolt them together. Easy enough. A dowel pin beside each blade will keep things aligned nicely. After bolt up, use the lathe to true it all up and it should be pretty well balanced at this point. So far we have turned all of this out on a lathe with the part in a rotating chuck.


   Now to get the holes for the blades, you have to drill at a right angle to the face which is in the plane of rotation of the chuck. And, this hole has to be precisely aligned at 120 degrees, but be true in both axes to make sure 1. The blade tips are equidistant and 2. The tips operate in the same rotational plane i.e. tips track in the same plane. I suppose one could turn out the piece then move it to the tailstock end on a degree wheel and chuck the bit to drill the holes, but I figure for a reasonable cost I could make the blanks and have the NC mill do it precisely. I could get my 16 year old to turn out the blanks on my lathe and maybe make a couple of sets then take it a couple of miles down the road and it's done.

   Kevin Alderman

Kevin, the lathe is a truly a  versatile machine. Some lathes, like my old Colchester have t-slots in the cross slide, making it very east to bolt down a rotary table. you then have to shim it up to center line with your work piece installed on the rotary table. Then just a matter of lining things up, and installing the adjustable boring bar in the lathe chuck, or spindle bore. rotate the rotary table every 120 degrees, and you have it.

Steve carlisle

Good idea Steve.
I made a cross slide grinder for mine.

Paul Lamar

   The Rotary Engine free News Letter. Powered by Linux. If you want off
   the list PLEASE let me know and I will remove  you.  ACRE NL web
   site. http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
   Copyright 1998-2017 All world wide rights reserved.